Question about 2006 Honda Accord

1 Answer

My turn signals, both on the dash and the actual lights are not working, hazards either, i checked fuses and thats not the problem any suggestions?

Posted by on

  • laurenaureli Nov 17, 2009

    so what if i dont know how do this... do i take ot to go get diagnosed?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

All the power goes to the turn switch (multifunction Switch). You will have to disassemble the steering cover and check for the proper voltages while testing. Also before you do any of this try wiggling the lever up and down and back and forth. It may start to work which could indicate the assembly as being bad. This is a common problem. Also you have a signal flasher in or around the fuse box. This also could be bad. They are usually silver in color. If the system was working correctly you would feel the flasher click while blinkers were activated

Posted on Nov 17, 2009

  • Ernset ( Skip ) Bouvette

    Just about any repair shop can fix this. The dealer will cost the most so choose wisely my dear



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Turn signals not working, Toyota Tundra 2000

Hazards work only when lights are off. Left signal light stays lit on the dash and does not blink and is stuck on (lit up) when lights are lit. If I place hazards on while lights are on only right side flashes and whole dash lights flash too... I replaced the flasher relay and it still does not work. Suggestions anyone? Thanks!

Apr 30, 2012 | 2000 Toyota Tundra

1 Answer

Can,t get signal or flashers to work on 1997 Dodge Intrepid

I assume you've checked the Fuses :p Obviously that hasnt worked and the bulbs and lights haven't worked either... SO try this????
Open the driver's side door and examine the end of the dash for an access panel. Behind the access panel are fuses and flashers. There are two flashers inside the access panel for controlling the turn signal and the hazard lights. You can distinguish them apart from each other by turning on the hazards or the turn signal and feeling for the clicking. If you turned on the hazards, then the flasher that is clicking is the hazard flasher.
Remove the turn signal flasher from the dash and reinstall the new flasher into the vacated slot in the dash. Close the access panel and start thetruck . Check the turn signals for proper operation and make sure the hazards work as well.

Please let me know how it goes
  • Jan 07, 2012 | Cars & Trucks

    1 Answer

    My turn signals will not turn on outside or in the dash

    if you check fuses to turn signal lights and hazard fuse problem could be in hazard switch or multifunction switch.

    Nov 22, 2011 | 2003 Oldsmobile Alero

    1 Answer

    I have a 2005 GMC w-4500 cab over box truck. The turn signals do not work. I have checked the fuse in the glove box, checked the flasher under the dash. The hazard lights work, but neither turn signal.

    that could have two flashers one for the turn signals and one for the hazards lights.if you turn the hazard lights on and the flasher you located, you should feel it click as the lights flash.if it does it could possibly have another one for turn signals. sometimes it is a square relay in the fuse panel. and could be a problem with the turn signal switch this is the same as a isuzu npr.

    Sep 15, 2011 | GMC W3500 Cars & Trucks

    2 Answers

    No brake lights, turn signals, or 4-ways.

    Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

    Your brake lights may be your brake switch just above your brake pedal.
    The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
    Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

    Sep 10, 2009 | 1998 Chevrolet Blazer

    2 Answers

    My hazard lights work but the turn signals wont

    Have you tried changing the flasher unit (the small plugin unit that makes the click sound when flashing)?

    These units come in several variations - perhaps an unsuitable unit has been installed.

    If none of the above suggestions help, you should re-check the operation on the turn signal switch.
    In one of the turn positions, if you bridge out the 2 correct pins of the flasher unit, the indicators on one side should light when you move the switch to that position.
    Move the switch to the other turn position, and the indicator lights on that side should light.

    If none of the above helps, you will need a vehicle wiring diagram to help find the problem.

    Jun 11, 2009 | 1994 Chevrolet Cavalier

    Not finding what you are looking for?
    2006 Honda Accord Logo

    Related Topics:

    27 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts


    Level 3 Expert

    79865 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Kevin Daniels

    Level 3 Expert

    1455 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides