Question about 2002 Ford Explorer

1 Answer

I need to find the air distribution blend door

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 819 Answers

This is a big job. the majority of the dash needs to come out so you can get the airbox out.

Posted on Nov 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001Chevy tohoe Cold air blowing threw back vents but not front vents?


When AC on and cold air from rear but not front is usually a blend door/heater box issue. You may have a non functioning blend door motor that controls hot/cold distribution of airflow

Jun 14, 2015 | 2001 Chevrolet Tahoe

1 Answer

How do i fix a stuck blend door on 2010 dodge nitro?


I would pull off the blend door actuator and swap it out with a new one. Or another option is to swap it out with one of the other actuators. The blend door actuator is interchangeable with the actuators for the mode-air doors and the recirculation-air door.

Disconnect and isolate the negative battery cable.

If equipped, remove the silencer from below the driver side of the instrument panel.

Disconnect the wire harness connector from the blend door actuator located on the driver side of the air distribution housing.

Remove the two screws that secure the blend door actuator to the actuator mounting bracket and remove the actuator

Feb 17, 2015 | 2010 Dodge Nitro

1 Answer

08 dodge nitro blows hot air on passenger side but cold air out the drivers side!! Any answers




NOTE: LHD model shown. RHD model similar. All vehicles are equipped with a common heater, ventilation and air conditioning (HVAC) housing assembly (1). The heating-A/C system combines A/C, heating, and ventilating capabilities in a single HVAC housing mounted within the passenger compartment behind the instrument panel. The HVAC housing assembly includes:
  1. Mode-air doors (2)
  2. A/C evaporator (3)
  3. Recirculation door actuator (4)
  4. Air inlet housing (5)
  5. Recirculation-air door (6)
  6. Blower motor (7)
  7. Blower motor resistor (8)
  8. Heater core (9)
  9. Air distribution housing (10)
  10. Blend-air door (11)
  11. Blend door actuator (12
  12. Floor distribution ducts (13)
  13. Mode door actuator (14)

Jan 28, 2015 | 2008 Dodge Nitro

1 Answer

Interior blower only blows up to warm on 1997 A4 2.7ltr


Check the blend door cable for proper attachment to the control panel and to the blend door. Try opening the door manually to see the you can get hot air out. If not, the door may be broken inside the heater box. If yes, correct/adjust the cable attachment for proper operation.

REMOVAL & INSTALLATION
1990-97 Passat Models
Install the cable ends marked with a white or blue band to the control head assembly. The cables must be attached to the control head before connection to the system air flaps.
  1. Remove the climate control head from the center dash assembly to access the control head cable ends.
  2. Remove the lower dash panels as necessary to access the cable lever arms.
  3. Attach the airflow distribution cable (cable 2) to the airflow distribution knob's lower control lever.

This cable can be identified as follows:
Operates the mode/central air flap Cable has a black sleeve and is 25.0 inches (634 mm) long Cable is marked with a white band
  1. Press the cable's sleeve against the control head stop and install the retaining clip.
  2. Attach the temperature control/air blend cable (cable 3) to the air temperature knob's control lever.

This cable can be identified as follows:

Operates the temperature control/air blend cable air flap Cable has a blue sleeve and is 21.0 inches (535 mm) long Cable is marked with a white band
  1. Press the cable's sleeve against the control head stop and install the retaining clip.
  2. Attach the airflow distribution cable (cable 1) to the airflow distribution knob's upper control lever.

This cable can be identified as follows:


Operates the footwell/defroster air flap Cable has a black sleeve and is 37.5 inches (954 mm) long Cable is marked with a blue band
  1. Install the cable such that the blue band is over the retaining clip mount and install the retaining clip directly over the blue band.
  2. Install the climate control head.
  3. Set the air flow distribution knob to defrost.
  4. Connect the longest airflow cable (cable 1) to the footwell/defroster flap lever on the heater's air box.
  5. Press and hold the flap's lever toward the retaining clamp perch and install the cable retaining clip.
  6. Set the airflow distribution knob to the Vent position.
  7. Connect the short airflow cable (cable 2) to the central/mode flap's lever.
  8. Pull and hold the mode flap's lever away from the retaining clamp perch and install the cable retaining clip. Check the operation of both air flaps making sure they can be heard contacting their stops.
  9. Set the temperature control knob to full cold.
  10. Connect the blue-sleeved cable (cable 3) to the air blend/temperature flap's lever.
  11. Pull and hold the mode flap's lever away from the retaining clamp perch and install the cable retaining clip. Check the operation of the air blend/temperature flap making sure it can be heard contacting the stops.

11_24_2011_10_52_22_pm.gif

Fig. Side view of the control head and cable location. 1. Footwell/defrost flap cable-2. Air distribution cable-3. Temperature control flap cable

11_24_2011_10_53_58_pm.gif

Fig. Temperature flap cable location and adjustment

Nov 24, 2011 | 1998 Audi A4

5 Answers

My 1997 ford f150 heater will not blow hot air. i have replace the switch that controls the hot and cold air. i do not know what else to do. i do not heat any vacuum noise when i switch it to the heater or...


first, check under te hood to see if the heater core water hoses are hot going in and coming out. If hot going in but cold coming out, water valve (if you have one) may not be working.
------------------------------------------------------------------------------------------------
Control System Outputs
The air management doors are controlled by vacuum control motors (18A318) and an A/C electronic door actuator motor (19E616). The air inlet and distribution doors are controlled by vacuum control motors. The temperature blend door is controlled by the A/C electronic door actuator motor.
The A/C electronic door actuator motor provides a variable number of temperature blend door positions. Temperature control position energizes the A/C electronic door actuator motor moving the temperature blend door.
Vacuum control motors are used on both air distribution and air inlet doors. The air inlet and panel/defrost doors use a two position vacuum control motor. The floor duct/panel door uses a three position vacuum control motor. Vacuum control motors are controlled by engine vacuum through the climate control head.
For more information on the control components Section 412-04 .
-------------------------------------------------------------------------------------------------------------------------------------
Air Management Doors
The air management doors are controlled by vacuum control motors (18A318) and an A/C electronic door actuator motor (19E616). The air inlet and distribution doors are controlled by a vacuum control motor. The temperature blend door is controlled by the A/C electronic door actuator motor.
The A/C electronic door actuator motor provides a variable number of temperature blend door positions. Temperature control position energizes the A/C electronic door actuator motor moving the temperature blend door.
Vacuum control motors are used on both air distribution and air inlet doors. The air inlet and panel/defrost doors use a two position vacuum control motor. The floor duct/panel door uses a three position vacuum control motor. Vacuum control motors are controlled by engine vacuum through the climate control head.
-------------------------------------------------------------------------------------------------------------------
Section 412-04: Control Components - Climate Control 1997 F-150, F-250 Workshop Manual
REMOVAL AND INSTALLATION A/C Electronic Actuator
Removal
  1. Remove the floor duct panel.
    • Remove the two plastic push pins (one each side) and release the expander clip.
  1. Remove the RH instrument panel brace.
    1. Remove the lower nut.
    1. Remove the upper bolt.
    1. Remove the brace.
  1. Remove the LH instrument panel lower nut and position brace out of the way.
  1. Disconnect the vacuum harness from the vacuum actuator.
  1. Remove the floor duct.
    1. Remove the two screws (one each side).
    1. Remove the floor duct.
  1. Remove the panel/floor door vacuum control motor.
    1. Disconnect the vacuum line connector.
    1. Remove the two panel/floor door vacuum control motor screws.
    1. Slide the rod out of the door and remove the panel/floor door vacuum control motor.
  1. Remove the electronic actuator.
    1. Disconnect the electrical connector.
    1. Remove the three screws.
    1. Pull down to release the actuator shaft and remove the electronic actuator.

Jan 24, 2011 | 1997 Ford F150 Regular Cab

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

How to replace a Blend Door Actuator on a 2000 Dodge Ram 2500 Conversion Ram Van? The air blows out the top, but will not blow out the vents.


Blend door mixes hot and cold, not a distribution control. Look for loose or dislodged vac lines... Heater designed to fail in defrost mode.

Sep 06, 2010 | Dodge Ram 2500 Cars & Trucks

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

1 Answer

Blend Door on 98 Ford Explorer


the blend door is roughly in the middle of air distribution Plenum assembly between the heater core and the AC evap core, it either directs air through the heater core or the AC evap core or mixes air from both.

Jan 14, 2009 | 1998 Ford Explorer

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
2002 Ford Explorer Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...