Question about 2002 Mercury Cougar

1 Answer

Any tips on removing the front seats on my 2002 Mercury Cougar? The Driver seat is electric power and the pasenger is manual. I want to swap them for an upgrade. The upgrade seats are an exact match except they are leather.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 106 Answers

Yes, this should work, all you need to do is to un bult the 4 bolts on the bottom of the seets that are attached to the floor board. And just unplug the electricle

Posted on Nov 17, 2009

Testimonial: "Thanks for your response"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location of the fuel pump driver module on a 2001 mercury cougar


This module is located behind the interior side trim panel, LH side behind the front seat, below the rear LH side glass. AKA B Pillar trim panel. Access from inside, probably will require removal of the rear seat bottom and even top of seat to remove the panel. it will be the small box in the center of that area once the panel is removed. Good luck!

Sep 20, 2014 | 2001 Mercury Cougar

1 Answer

How do i remove the driver seat in a 2000 mercury cougar when i can not reach the bolts and the seat does not move


You just have to get the bolts out. The rear bolts can be somewhat difficult when the seat is back and will not move forward. In this case, remove the front bolts first. Then you will probably have to use a wrench to get to the rear bolts. There is usually not enough room to get a ratchet and socket in there.

NOTE: GEARWRENCH makes ratcheting wrenches that are perfect for jobs like this one. They give you the convenience of a ratchet, while providing you with the clearance of a wrench. For more information on this go to gearwrench.com.

Anyway, to get enough clearance for the bolt to come all the way out, (or the nut to come all the way off if your Cougar uses nuts in the rear) you may have to work both rear fasteners at the same time and tilt the seat forward as you go (Which is why we took the front bolts out first). This is especially true if you are using a box-style wrench. Be sure to loosen each bolt incrementally so the seat CAN be tilted to avoid getting your wrench trapped.

Once all the bolts are out, you can tip the seat backward to access the wiring connectors under the seat to disconnect them.

Sep 11, 2011 | Mercury Cougar Cars & Trucks

1 Answer

CANT FIND RELEASE TO REMOVE BACK SEAT FROM 2000 MERCURY COUGAR


You have to push down real hard with your knee on the front side of the back seat and at the same time with your hands, push the seat back towards the trunk..You have to do the same thing on the other side.(two wire locks one on drivers side and one on passanger side).
Hope you understand this???

May 22, 2011 | 2000 Mercury Cougar

1 Answer

Where is the airbag module located on my 02 Mercury Cougar? Thanks...


raineman_15_6.gif This picture is forYour air bag diagnostic monitor and also your driver air bag module &sliding contact. Your side air bag modules are at respective side of each front seat

Dec 02, 2010 | 2001 Mercury Cougar

1 Answer

Were is the flasher in a 1990 murcury cougar


For 1990 Mercury Cougar 3.8L FI 6cyl the Flasher is located: Front seating area, driver side, under dash, mounted on passenger side of steering column.

I hope this helps (remember to rate this).

Nov 18, 2010 | 1990 Mercury Cougar

2 Answers

We cannot remove 2nd seat in our 02 Kia Sedona. We


move seat completely back.take off head restraint,tip backrest forward flat to seat, then, grab the pull cord and pull backward so that seat tips forward then grab bars on front of underseat and squeeze together and lift.be careful these seats ARE HEAVY.

Feb 22, 2010 | 2002 Kia Sedona

1 Answer

How to remove a drivers seat


rremove the 2 bolts in front of seat at the bottom and two at the rear bottom of seat then tilt seat and disconnect wiring and remove the seat, good luck, hope this helps.

Dec 19, 2009 | 1999 Mercury Cougar

1 Answer

1998 Cougar power seat works in all directions except forward


THE MOST COMMON CAUSE OF THIS IS THE SEAT SWITCH (WIGGLE THE SWITCH WHILE YOU TRY TO MOVE THE EAT), IF THAT DOESN'T FIX IT U WILL NEED TO REPLACE THE POWER SEAT TRANSMISSION, A VERY EXPENSIVE PART, SO TRY THE SWITCH 1ST.

Jul 06, 2009 | 1997 Mercury Cougar XR7

1 Answer

Seat belt chime will not stop until ignition is turned off. mercury cougar 92


the wire under driver seat must have coom loose from the seat belt clip

Dec 04, 2008 | 1992 Mercury Cougar

Not finding what you are looking for?
2002 Mercury Cougar Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...