Question about 2000 Isuzu Trooper

2 Answers

Isuzu 3.0 trooper no drive when in gear pressure

Isuzu 3.0 trooper no drive. when in gear pressure plate stops turning when clutch pedal is let out,but turning ok when pedal is pushed back in is there a problem in the flywheel . pressure plate is bolted to flywheel ok so how could it stop turning when a gear is selected

Posted by on

  • mtatnall May 11, 2010

    will the engine stall if you let out the clutch in gear?

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 235 Answers

Bad news . you have a DMF - dual mass flywheel which has two moving parts  joined by springs to take the shock out the driveline  - only trouble yours might have just one ! Only way to know for sure is to drop it all out but it is a know fault when the drive goes like yours.
Go to ITOCUK.CO.UK and see the posts by red robbo for some good pictures to see whats what .

Posted on Nov 18, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi found out that it is a dual mass flywheeel and its allowing this problem as its faulty

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Isuzu Trooper clutch is vibrating and making it hard to go into gear how do you fix it


the throw out bearing is damage.
classic.
or the clutch fingers in the pressure plate or warpped
but that dont matter, as both are same job. (same work)

Jul 05, 2014 | 1995 Isuzu Trooper

1 Answer

1986 isuzu trooper clutch pedal went soft


some of these were manual clutch cable check adjustment of cable at firewall (bulkhead) and check for cracks around where cable goes through to inside cab common on old girls.
if hydraulic clutch system
check fluid in clutch master cylinder is it low?
it could have leaking slave cylinder on gear box bell housing or your clutch needs replacing, gear box out and replace clutch as a kit, pressure plate, clutch plate, thrust bearing (comes as kit) but dont forget to check and or replace the spigot bearing in the rear of the crank shaft when doing clutch kit.

Apr 01, 2014 | 1986 Isuzu Trooper

1 Answer

What could be the problem?


have the cpu reset with a fault code reader and you problems will go or will be explained to you.

Jun 02, 2013 | 1996 Isuzu Trooper

1 Answer

Transmission won't ingage


Sounds Like Pressure Plate Or Clutch Plate Are Worn Out ,You Could Check The Slave Cylinder To See That It Is Going Full Travel In And Out As You Operate The Clutch Pedal

Mar 29, 2013 | 1988 Isuzu Trooper 2 Door

1 Answer

We have a manual transmission Isuzu Trooper 1995, the gears will not change but car starts and drives in this one gear. The clutch is fine, doesn't stick or anything. What might the problem be?


The pressure plate to the clutch is not dis-engaging the tranny...most likely need a pressure plate and clutch change...Hope this helps.

Apr 25, 2011 | 1995 Isuzu Rodeo

2 Answers

Manual Transmition, While driving the clutch pedal went right to the floo and stayed down. I lifted the pedal with my foot and with a light touch i pushed down on the pedal and it it began a grinding sound...


the slave cylinder on the trans works just like a brake cylinder, when fluid pressure is applied it flows into the cylinder and pushes against a clutch fork which engages a throw out bearing against the clutch pressure plate fingers. a couple things could have happened. I think your trans is fine but im sure the clutch fork or the pressure plate broke. I'm sorry but the trans is gonna have to be pulled. best wishes

Feb 03, 2011 | 2000 Isuzu Trooper

2 Answers

2001 isuzu trooper transmission is slipping when accellerating


Well if its a Auto matic, then you have either low in oil, or if level ok then its either the micro filter in the oil pan on the box ,or the body valve that lets the pressure go to the pistons which drive the forward and reverse driving belts ( which work the oppersite to the brakes which stop you these make you go).
BUT if a Manual gear box then its due to the clutch assy or the imput shaft broken in the centre plate
Let me know how you get on . RON

Nov 17, 2009 | 2001 Isuzu Trooper

2 Answers

Clutch slipping when it get hot


Check the adjustment of the clutch push rod. It is the rod that connects the clutch pedal to the clutch master cylinder.

Dec 22, 2008 | 1992 Isuzu Amigo

Not finding what you are looking for?
2000 Isuzu Trooper Logo

Related Topics:

376 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...