Question about 2002 Jeep Grand Cherokee

1 Answer

Govenor sensor too high - 2002 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 67 Answers

Please state what type of trans you have? need to inspect voltage at sensor very common on 46re sensor replacement but also valve body

Posted on Nov 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE A CHECK ENGINE LITE ON, CODE SHOWS GOVENOR SENSOR VOLTSGE TO LOW OR TO HIGH. I REPLACED BOTH THE SENSOR AND SOLINOID ABOUT 13 MO AGO.IS IT POSIBLE THEY FAILED AGAIN.


why not post the code and not make us guess.???
no, it didnt fail again, someone guessed wrong.

take car to any ASE shop or transmission shop and win.
they will do diagnosis and find the real cause.

no code, no joy.

2000 wj

RTM yet,
here
http://www.morris4x4center.com/knowledge-base/index.htm?utm_source=cj#service

see those pages on DTC errors. p07xx errors. and friends
and the statements on how to test further.....

Dec 17, 2015 | 2000 Jeep Grand Cherokee

1 Answer

1988 CHEVY S-10 PICK UP IDLES HIGH


Peck on it with something to see if it idles down, if it does you probably need a new idle positioning sensor.

Jun 24, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

I have a 98 dodge ram 2500 5.9 4x4 automatic with o/d will not shift out of low untill a mile or two down road then does fine, had a service done and foung half of a clutch band in pan with metla shaving...


Aluminum metal shavings are very normal for this transmission if the pan has never been off.What do you mean by "clutch band".This unit has 4 sets of clutches 2 bands and 2 rollers clutches.I would suspect a bad govenor pressure sensor and or solenoid by the symptoms you describe.With a scan tool you can look at govenor pressure(actual)and desired govenor pressure.Govenor pressure should be at 0 sitting still and should increase with road speed( example 22 mph=22psi). Let me know if I can help.

Feb 13, 2011 | 1999 Dodge Ram

1 Answer

My 1998 Jeep Cherokee will start but will not shift out of first gear. Any solutions?


Is the check engine light on? Does the speedo work? Probaly is either a bad output speed sensor on the trans tail hosing or a bad govenor pressure solenoid and /or pressure sensor on the valve body. Need to have it scanned. Output rpms should be zero at a stop and increase with road speed . Govenor pressure should be within 3 psi of desired govenor pressure . Desired govenor pressure should match road road speed.I would recomend replace the sensor and solenoid as a pair.Please vote and good luck!

Jan 21, 2011 | 1998 Jeep Grand Cherokee

1 Answer

My 97 4l auto is not shiftin thru gears quick enough in the mid range, any advice?


Common problem is govenor pressure sensor and the govenor solenoid. With a scan tool you can see gov pressure and desired gov pressure. Govenor pressure should almost match vehicle speeed ( 15 mph = 15 psi ) . If govenor pressure is eratic or high or low in rlationship to desired gov pressure replace the sensor and the solenoid. Will need to pull the pand to do this.make sure when you check the fluid you check it in NEUTRAL with the engine running and not park.

Jan 11, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Code p1762 govenor pressue sensor offset volts


P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Dec 14, 2010 | 2001 Jeep Grand Cherokee

1 Answer

How take out in disconnecting the governor pressure sensor from transmition jeep?


To remove the govenor pressure sensor you have to drop the pan,remove the filter,take the torx screw out of the bracket that holds the sensor unplug the sensor and wiggle it while pulling back on it.

Sep 30, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Grand Cherokee laredo P1763 and P1762


It's a transmission related problem, that you should have looked at a.s.a.p. to avoid costly transmission repairs down the road. Have it scanned at a reputable transmission repair place, dealer, or mechanic you trust. The drain pan will have to come off to perform repair, so have a transmission service (filter & fluid) done while your at it, unless it was done recently.

Jan 30, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Chev cavalier 2.2L IAT sensors location (non ECOtec)


Your IAT sensor is going to be on the intake tube.
the connector you should see is a oval two wire connector. (the normal for chevys) the other connector going to the intake tube is the mass air flow, these usually have 4-6 wires.
I can't help you with your govenor problem

Jan 27, 2009 | Chevrolet Cavalier Cars & Trucks

2 Answers

1999 jetta not going over 75 mph


your car has a speed govenor on it if you want it to go faster take it to a shop that can reprogram the speed govenor

Jul 07, 2008 | 1999 Volkswagen Jetta

Not finding what you are looking for?
2002 Jeep Grand Cherokee Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...