Question about 1987 Ford Mustang

1 Answer

When does stuff start going wrong with an 1987 ford mustang lx 2.3l 4cyl? it has just over 248000k on it right now.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

About 1987.

Posted on Nov 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have 1993 mustang lx with 2.3 automatic. when you put it in reverse it jerks hard and stalls the engine. whats wrong?


Check your transmission oil dip stick....look at the color of it. If its Brownish Black in color tranny is toast. Start there. Hope this helps you to start with.

Mar 21, 2014 | 1993 Ford Mustang

1 Answer

Need a wiring diagram for 1986 ford mustang 4cyl engine. Helping a friend with his 4cylinder mustang and when i installed the negative terminal on the battery then as i place the positive terminal it...


Hi!!

You may have the positive cable hooked in the wrong side of the starting selenoid or the starter selenoid is defective.

Follow the RED (+) cable from the battery, it goes to the starter selenoid wich has two terminals, change the cable to the other terminal, that should take care of the problem unless the selenoid is stuck on. Replacement runs about $15.

Don't forget to rate this post. Good Luck!!

Jul 06, 2010 | 1986 Ford Mustang

2 Answers

I have to replace the oil pump, but the mechanic said that after i replace the pump the engine might still make noise. what can cause the engine noise after i replace the pump? how can i fix it? its a 1987...


Why replace the oil pump? That won't make noises go away or cause noises. Your mechanic should be able to answer theses questions, as to the cause of noises.

Mar 10, 2010 | 1987 Ford Mustang

1 Answer

Where is the 1987 Mustang LX 2.3 Liter Fuel Filter Located?


Hi,

Location - Under vehicle, passenger side, below seating area, front of fuel tank, mounted on frame in fuel line.

Let me know, if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Dec 07, 2009 | 1987 Ford Mustang

1 Answer

1990 ford mustang lx 4cyl, auto blew out it's transmission fluid. what caused this? new seal and fluid, seems to be fine. is is okay now?


a Plugged vent on the tranny could cause this and an overfill of transmisson fluid could cause this, but without inspecting it would not know the cause or if it would strand you again?

Jul 06, 2009 | 1990 Ford Mustang

1 Answer

1992 ford mustang lx 2.3L will not start


The crankshaft sensor went bad. I Was'nt getting any fire from the coil pack. Tried switching coils and still nothing, tried switching ignition modual, nothing. I checked to make sure it was in time and it was. Nothing left to check so I changed the crank sensor and it firerd right up! Thanks.

Jun 13, 2009 | 1992 Ford Mustang

1 Answer

I have a 92 mustang lx 4cyl. timing belt broke and now i have the cover and pullys off but can not get the new one on cause it appears to be a crank senser in the way! how do i go about getting it off?


check first if this is called a safe engine first as you do a lot of damage to the engine if the timing belt broke such as valves and otheres

Mar 30, 2009 | 1992 Ford Mustang

1 Answer

Mustang will not start


You'll have to mark number one position on the side of the distributor. remove the cap and point the rotor to the mark that you just made and stab it into the engine. I may not go in right away, just keep trying.

Nov 08, 2008 | 1987 Ford Mustang

1 Answer

1983 Mustang C-4 transmission


that trnas will not bolt up and since you don't have a computor control the trans wount interface with the harness it requires which you do not have on your vehicle. please rate this solution

Aug 30, 2008 | 1983 Ford Mustang Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...