Question about 2002 Dodge Dakota Club Cab

Open Question

2002 dakota 4x4 service light on indicater light out wont shift into 4 hi or 4lo

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 512 Answers

SOURCE: Service 4x4 warning light on.

you need to take it to a dealer or reputable independant and have the 4wd system check...the transfer case controller is detecting some fault in the system

Posted on Oct 01, 2008

  • 78 Answers

SOURCE: 2001 S10 stuck on 4 Lo

are you shure its stuck?,will it go to 2-wd? if it does,try to reset the comp' by disconnecting battery for one or more hours!

Posted on Dec 27, 2008

  • 1 Answer

SOURCE: 2002 kia 4x4 wont go into 4 wheel drive

Hello
A VERY COMMON FAULT!
Kia us a dim design that works on air, so the light on the dash may light up green...mine does...but no 4x4.
Test one, look inside the engine bay,(2Litre petrol) on your left hand side, to the left of the actual engine is the solenoid device that "switches on" the vacuum to the front hubs. This is easier that you would think. If you look at the left side of the engine, there are two pipes coming out (left side) one is thick (break system. DONT touch) one is thinner and soft rubber. Follow this tube, it goes into a small black cannister which is a resvoir and one way valve...the tube then outputs into another device (solenoid) which has 2 wires on. The tube then splits under this in two. The test is simple, with the engine running, and 4 wheel drive engaged pull the tube apart after the solenoid. Put your finger there you should feel a nice strong ****. If it does **** put it back on. If it does not **** it needs to be removed and cleaned. This is simple to unbolt and all you do is pull the rubber bung of the bottom, and the two tubes and spray break cleaner inside. reassamble until you get to feel the vaccum.

test 2 Now look behind each wheel, you will see a thick hose wrapped in a spring, this is the break system, do not touch this. There is a thinner flexible hose attached behind the wheel, you will notice that these have no securing system just push fit. Remove each of the in turn and test for vacuum.

Leaks here are common and easy to fix.

The bad news if you have vacuum, and still no 4 wheel drive one or both front wheel hubs has a leak, and the bad news is, it needs a garage to fix it, and to replace the seal a £5 part you have to ruin a £100 part.

Test the vaccum, pray. Otherwise ask, doe you really need to spend £250 to sort this?

Good luck

Posted on Mar 17, 2009

emissionwiz
  • 75822 Answers

SOURCE: 2002 dodge dakota engine misfire and service engine light on

if you correct the miss the trans will shift correctly, the engine miss set a trouble code, that will ID the cylinder that is missing, have the trouble codes tested

Posted on Aug 24, 2009

  • 67 Answers

SOURCE: 97 dodge dakota 4x4 with the v-8 and 44re trans

get the codes with scanner first,somethig is wrong in valve body,some valve,you should do a pressure test in each port in the trany,you know the plugs in the sides ok,if there is not the especific pressure some valve is not moving free or is stuck,look for speed sensors ectr,#1 scanner for codes ok.

Posted on Nov 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shifting 4x4 4lo


Most likely cause is the encoder motor on the transfer case.

Oct 26, 2013 | 2002 Chevrolet Silverado 1500

1 Answer

2005 Sierra 4x4 doesn't work, 4h light is on and stays on


My 2005 Sierra 4x4 did the same thing while running down the interstate on vacation. Scared me to death, thought it was going to shift into 4 wheel drive @ 80 MPR. Had to take to shop and they found a censor bad and they replaced it. Don't know cost, because truck was still under warranty.

Nov 22, 2012 | 2005 GMC Sierra

1 Answer

2000 gmc 4x4 shifting problem


change your push button switch had same problem

Nov 24, 2011 | 2000 GMC Sierra

1 Answer

My 4X4 won't shift into 4Lo but it will shift into 4X4 Hi and anti 4X4,. What could be the problem? It's on a 2004 Chevy Trailblazer.


On some GM vechiles with 4x4, you have to put tranni in netural, then try to shift into low 4x4. Same thing when you're done with 4 low trying to go back to 2 or 4 hi.

May 30, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Will not shift into drive also indicater light on shift not working sometime


? fuses also make sure you didnt set the transfer case to tow mode do you see red light if yes hold 2wd and 4lo at same time to reengage transmission

Feb 15, 2010 | 2003 GMC Sierra

1 Answer

2002 s10 4x4 quad cab wont engage into 4hi or 4lo the clicking sounds that i have heard before when it did work is still there .the transfercase does change gear ratio in 4lo. today i tryed 4hi it did not...


Does your s10 have electronic shift or manual shift? Most i have seen are electronic shift try checking the shift motor on the transfer case, they have a tendency to corrode and split open the case. hope this will you

Jan 28, 2010 | Chevrolet S 10 Cars & Trucks

2 Answers

1986 s10 4x4,transfer case,loose manual shifter


theres locking pins that hold it in gear that kind of resemble a door latches it`s my guess that there springs are no good and they just are staying open allowing it to slip back out of gear.

Jan 01, 2010 | 1987 Chevrolet S-10 Pickup

1 Answer

02 dakota wont shift from 4hi to 2 hi


Try commanding the drive ranges while in netural cycling them. This may normalize the controller that senses the position from the encoder motor assembly. There maybe a procedure for that in a service manual.

Dec 12, 2009 | 2002 Dodge Dakota Club Cab

2 Answers

4x4 not shifting into high


hi how are you doing? just had same problem with by gmc i replaced the transfurcase motor and it works fine. the electric motor moves the shifter in your transfurcase from 4hi to 4lo and 2hi.there is only 3 things that operate your 4x4 the switch the motor and the control modgual.

Jan 28, 2009 | 1994 GMC Jimmy

1 Answer

4x4 transfer case problems


ithink it might be just a bad senser

Jan 01, 2009 | 1998 Chevrolet Blazer

Not finding what you are looking for?
2002 Dodge Dakota Club Cab Logo

Related Topics:

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...