Question about 2002 Mitsubishi Lancer

1 Answer

Changing the starter - 2002 Mitsubishi Lancer

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 561 Answers

1 disconnect battery, but be sure you have any pin for radio etc so the will work again after.
2 get underneath and identify the starter motor.
undo the cables on the solenoid and the main cable on the motor.
3 remove the housing bolts to remove the motor from the engine.
on removal check the fly wheel to ensure there are not broken teeth or other problems.
4 on installation of the new motor reverse order points 3 back to 1.

Posted on Nov 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing a starter


disconnect the battery , remove the large battery cable from the starter, remove the small cable from the starter . remove the holding bolts from the starter, lift out the starter motor.

Nov 12, 2016 | Cars & Trucks

1 Answer

Car troubleshooting


use a code reader to reset the CPU as the program may be corrupted from the battery change.

Jan 08, 2014 | Cars & Trucks

2 Answers

I have replaced the starter and batteries and engine just clicks and starter gets hot


you have a faulty starter. you have to take it out.test it on the bench.
also check does the engine rotate ok.infect do this prior to taking the starter out.

Jan 11, 2011 | Ford F-450 Cars & Trucks

3 Answers

My 1981 Cadillac Deville 5.7L Diesel wont start. Ive checked all that I know including starter,battery,alternator,etc. Also, checked fuel pump, feul filter, fuel lines, injection pump. I topped off all of...


What does changing the oil,changing filters etc,have to do with the vehicle not starting?
What actual testing was done on --battery,alt,starter.fuel pump,etc.,how was this testing conducted and what were the results?
No fluids are consumed, in any motor vehicle,
If you have to top off,you have a leak,repair it!!

Sep 20, 2010 | Cadillac DeVille Cars & Trucks

1 Answer

My car is not starting. It makes a horrible rattling noise when i try to start it... I have been advised (non-professionally) that it could be the battery or the alternator. Any suggestions?


Have the battery tested to eliminate it as the problem. It should show 13-14 volts minimum. If the battery is good then the alternator is, by default, good as well. This honestly just sounds like a run of the mill starter problem to me though. Changing the solenoid is cheaper than changing the the whole starter and is probably enough but if you want it over once and for all, change the whole starter. A mechanic will charge more to replace the solenoid than the whole starter because there is a little more work involved but the cost of the whole starter may still make it the more affordable option. You could also check prices on having the original starter rebuilt.

Nov 28, 2009 | 2006 Peugeot 405

1 Answer

My starter kicks out before the car starts how can i tell if its the starter or celinoid


It's most likely the "bendix drive" in the starter kicking out. It's the part that engages the starter to the flywheel. Changing a starter without changing the solenoid is like having a slice of bread without any butter. Change them as a pair. Hope this helps.

Nov 27, 2009 | 1989 Oldsmobile Eighty Eight Royale

1 Answer

Not getting fuel after changing the starter motor just wondering if there a safety shut off switch somewhere or if my fuel pump and starter went at the same time!!!!!


It seems there may be a shut off switch or you may have pulled a fuel pump connection loose while changing the starter. Some cars have a emergancy shut off to fuel in case of collisions, mine have mostly been in the trunk. research emergency fuel cut off for your make and model and research no fuel for same.

Oct 22, 2009 | 1993 Buick Roadmaster

1 Answer

How to change starter selinoid


the starter selinoid is on the starter itself. normally a parts dealer will never seel you a starter selinoid individually but they will sell the starter with the selinoid. but you cant change the selinoid without changing the starter

Jul 09, 2009 | 1997 Chevrolet Camaro

Not finding what you are looking for?
2002 Mitsubishi Lancer Logo

168 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...