Question about 1998 Mercury Grand Marquis

Open Question

Need to remove the arm rest between the front seats of a 1998 Mercury Grand Marquis. The leather is torn and worn out and I'm trying to flip it around. Cant find how to get the arm rest free. no bolts?!

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 328 Answers

SOURCE: rear seat belt repair on

If simply pulling and releasing them doesn't work.(which i am sure you've already tried a hundred times!) you will have to replace them.Most scrap yards will have them available. and remember the same seat belts are used in a wide variety of models so you don't have to find them from the exact same car.
Good Luck!

Posted on Jan 17, 2009

  • 1 Answer

SOURCE: remove front door panel on 1995 merc grand marquis

http://www.autoclinix.com/Mercury/Front%20Speakers2.htm

Posted on Jan 17, 2009

  • 1 Answer

SOURCE: 1993 Mercury Grand Marquis

how can i tell if the relay is bad i got a new fuel pump

Posted on May 05, 2009

  • 1596 Answers

SOURCE: how to r&r powersteering pump 1998 mercury

Hopfully this will be ALL you need Besides Pulley REMOVAL TOOL It can be Rented @ AutoZONE

REMOVAL

  1. Remove drive belt.
  2. Raise vehicle on hoist. WARNING: TURN AIR SUSPENSION SWITCH (LOCATED IN LUGGAGE COMPARTMENT) OFF TO PREVENT VEHICLE DAMAGE OR PERSONAL INJURY.
  3. Remove power steering pressure hose bracket.
  4. Disconnect electrical connector at power steering control valve actuator.
    1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley hub. CAUTION: Do not apply in-and-out pressure on the power steering pump shaft. Pressure will damage the internal thrust areas.
    2. Hold the small hex-head and rotate the tool nut counterclockwise to remove the power steering pump pulley.
    3. Disconnect power steering pressure hose at power steering pump and drain fluid into a container.
    4. Disconnect power steering return hose at power steering pump and drain fluid into a container.
    5. Remove four retaining bolts and power steering pump and power steering pump pulley assembly.
    6. Remove power steering pressure switch from pump.
    INSTALLATION
    1. Position the power steering pump on the mounting bosses of engine block and install the bolts at the side of the power steering pump. Tighten to 20-30 Nm (15-22 ft. lbs.).
    2. Connect the power steering reservoir pump hose to the power steering pump and reposition the hose clamp to power steering pump inlet fitting.
    3. Replace power steering pressure hose O-ring.
    4. Install the power steering pressure hose to the power steering pump fitting. Tighten the tube nut with a tube nut wrench rather than with an open-end wrench. Tighten to 34-46 Nm (26-33 ft. lbs.). NOTE: Swivel or end play of the power steering pressure hose end is normal and does not indicate a loose fitting.
    5. Place the power steering pump pulley on the power steering pump shaft and install Power Steering Pump Pulley Replacer T91P-3A733-A. The small diameter threads on the tool should be engaged in the power steering pump shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group.
    6. Hold the small hex-head and rotate the tool nut clockwise to install the power steering pump pulley on the shaft. CAUTION: Do not apply in and out pressure on the shaft. Pressure will damage the internal rotating group. NOTE: The power steering pump pulley face must be flush within 0.25 mm (0.010 inch) of the end of the pump shaft.
    7. Remove the Power Steering Pump Pulley Replacer T91P-3A733-A.
    8. Remove the shipping tube nut from power steering pump housing prior to installation.
    9. Connect electrical connector to power steering control valve actuator.
    1. Install power steering pressure hose bracket.
    1. Lower the vehicle.
    2. If equipped, turn the air suspension ON.
    3. Install drive belt on the power steering pump pulley.
    4. Fill the power steering pump reservoir with Power Steering Fluid Motorcraft MERCON(r) ATF.

Posted on Oct 04, 2009

  • 106 Answers

SOURCE: Any tips on removing the front seats on my 2002

Yes, this should work, all you need to do is to un bult the 4 bolts on the bottom of the seets that are attached to the floor board. And just unplug the electricle

Posted on Nov 17, 2009

Testimonial: "Thanks for your response"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the top dash cap, not the whole dash, from a 1993 Mercury Grand Marquis


I covered one of mine with a custom dash mat...about $50. from JC Whitney...on line...much cheaper...leather is not usually used on top side of dash due to Sun rays...

Aug 05, 2015 | 1993 Mercury Grand Marquis

Tip

How To Install Replace Front Outside Door Handle Mercury Grand Marquis 98-11...


How To Install Replace Front Outside Door Handle Mercury Grand Marquis 98-11 1AAuto.com

on May 18, 2012 | 1998 Mercury Grand Marquis

1 Answer

How do I remove middle armrest on 2008 Honda accord sedan


Most likely 3 screws hold the armrest lid on.Towards the back.

Nov 12, 2014 | Cars & Trucks

1 Answer

How to replace pitman arm 1998 crownvic


just remove the nut on the bottom and you will need a pitman arm puller some stores will rent you one if this does not come off easy u can heat the arm up and hit it with a hammer to shock it loose.

Jul 25, 2010 | 1998 Mercury Grand Marquis

1 Answer

I am looking for the doors mirrors control switch for 1995 grand marquis located on the drivers arm rest


Try the Lincoln/Mercury Dealer Parts Dept

Go to salvage yard and get one from a deceased similar vehicle

May 12, 2010 | 1995 Mercury Grand Marquis

1 Answer

How to replace passenger side outside mirror on a 1997 Mercury Grand Marquis?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. You can then remove the bolts securing the mirror onto the door

Sep 18, 2009 | 1997 Mercury Grand Marquis

1 Answer

What are the igniton timing,firing order, spark plug gap specifications for 1998 Merc Grand Marquis with 400 cdl engine?


1998 Mercury Grand Marquis
4.6 liter V-8 VIN "W"

98d6a49.gif

I will get you the rest of the info in just a few hours...I am at work!

Aug 09, 2009 | 1978 Mercury Grand Marquis

Not finding what you are looking for?
1998 Mercury Grand Marquis Logo

Related Topics:

341 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...