Question about 2002 Nissan Altima

1 Answer

How do i change the radiator in a 2002 Nissan Altima 3.5L

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

WHAT IF I CHANGED THE RADATOR AND NOW ITS SMOKE COMING OUT?

Posted on Aug 24, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jschoon77
  • 55 Answers

SOURCE: DOOR WON'T OPEN FROM INSIDE OF NISSAN ALTIMA 2002 ON DRIVER'S SIDE

There is a cable that attaches to the inside door latch release handle. The plastic that retains this cable is most likely broken. I have seen this before. If the retainer is not holding the cable sheath correctly, the entire cable moves when the handle is pulled and does not release the door latch.

Remove the door panel and inspect this cable. You will see 2 cables (one is for the door lock). If the plastic is broken, you will need a new interior handle assembly.

Hope this is helpful!!



Nissan Scope Technician- 10+ years experience in Nissan dealership

Posted on Nov 11, 2008

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 54 Answers

SOURCE: Tune up nissan altima 2.5L model 2002

All you really need is a good set of spark plugs, this car has coil packs so no plug wires distributor caps etc.....Just remove the coil packs and install your plugs and your done. Good luck.

Posted on May 31, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

  • 1810 Answers

SOURCE: Nissan Altima tring to change my transmission fulid and filter

thats why you have to remove the frame and for this you need an engine support and the average mechanic will charge you arround 100 bucks to do it
some rental stores have them some dont good luck eithor way you go but for god sake be carefull

Posted on Dec 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change power steering belt


How To Change The Serpentine Accessory Belt On Nissan Maxima Altima Etc

Nissan Drive Belt Tensioner and Belt Replacement 3 5 Front Wheel Drive

There are several videos on how to change out the serpentine belt For more info just do a web search " 2002 Nissan Altima serpentine belt replacement".

May 26, 2014 | 2002 Nissan Altima

1 Answer

Nissan Altima 2002 Nissan Altima Takes long for heat to come out


You might try bleeding air out of cooling system. Elevate front of car on ramps and leave running. Remove radiator cap before engine gets hot. When engine starts to heat up, air bubbles may come out of top of radiator. Add coolant slowly as level drops. It may take a long time for car to warm up (15-20 minutes)

Nov 09, 2013 | Nissan Altima Cars & Trucks

1 Answer

How to replace driving light on 2002 nissan altima


FIRST OF ALL WEAR CLEAN GLOVES BECAUSE YOU HANDLING HALOGEN BULBS IF OILS FROM YOR HANDS GET ON BULB IT WILL BLOW THEM.TO GET TO BULBS YOU HAVE TO REMOVE HEADLIGHT HOUSING YOU HAVE TO REMOVE 2 TOP BOLTS SECURING HEADLIGHT HOUSING TO THE RADIATOR SUPPORT THEN YOU HAVE TO REMOVE RETAINING NUTS SECURING THE INNER END OF THE HEADLIGHT HOUSING FROM BEHIND THE RADIATOR SUPPORT.YOU NEED A MANUAL TO SEE WHERE YOUR HEADLIGHT SECURING BOLTS LOCATED.

Aug 30, 2010 | 2002 Nissan Altima

1 Answer

How to put belt back on for a 2002 nissan altima


if there is no white label on top of the radiator guard,
If you buy your belt from Autozone the belt routing is on the package,If you already bought the belt you could always buy one from AutoZone and then return it after you use the routing.

Jan 26, 2010 | 2002 Nissan Altima

2 Answers

Flush the radiator


wins radiator flush

Jun 01, 2009 | 2002 Nissan Altima

1 Answer

2002 nissan altima headlights


you need to remove the grill etc etc the you will be able to change the lights.

Jan 03, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...