Question about 2006 Volkswagen Golf

1 Answer

Change headlamp bulb on vw polo 2006 - 2006 Volkswagen Golf

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 60 Answers

Open the hood/bonnet and you should see the back of the headlights in the front corners of the engine compartment. Look for bolts/sping-clamps that are holding them in place, and remove. Slide the headlight out so you can reach the bulb, remove the old one and replace. Reverse the removal procedure to replace the headlight

Posted on Nov 17, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 181 Answers

SOURCE: iNEED TO CHANGE HEADLAMP BULB HOW DO iTAKE OUT

heres instructions and picture

f90e8cf.gif7a16af1.gif

Posted on May 07, 2010

3dmaster
  • 183 Answers

SOURCE: 2001 vw polo

Dear Customer,

1
check your sensors 1st,all sensors must be good

2
if all sensors are working good than check your engine firing sequence,some times happens when sequence was wrong,

3
check your exhaust and carborator tuning pin that creates the batter combination for firing in bore for batter performance & less emitions ,so check is it ok or not than go to your nearest service center that havad certified mechanics,

till you read this you had solve this problem definatly,

THNX

Posted on May 18, 2008

SOURCE: How to remove head light in a 2006 VW Beetle

go here
http://wiki.answers.com/Q/What_is_the_procedure_for_headlamp_removal_on_a_2006_beetle

Posted on Oct 14, 2008

  • 89 Answers

SOURCE: removing plastic engine cover from 2005 VW Polo

the cover just pulls off and disconnect breather hose as u lift it.there is about 15 screws to remove then the cover opens

Posted on Jul 12, 2009

  • 324 Answers

SOURCE: Removing VW polo 2005 battery?

Removing a battery from a Beetle is a bit complex and tricky. I just changed the battery in a 2003 2.0 Beetle. However, the process is very similar in a TDI Beetle. You will need more than your standard generic tool set in order to complete this task. Your tool list needs to consist of a pair of pliers (prefer locking type), a # 20 TORX head screwdriver (You will also need this if you ever plan on changing the Beetle's internal dash pollen filter for the A/C. ), a 10 mm and 13 mm sockets, a long extension and a wobble or universal to allow flexibility in tight spaces, an allen socket for removing the power steering reservoir, and a small adjustable wrench or a 10mm to remove the battery cables. If you are changing the battery you might as well buy a new Air filter since you will need to remove the air box in order to replace the battery. If you do change the air filter you will need a phillips head screwdriver.

1. Pop the hood.
2. Remove the two 10 mm bolts that hold down the air filter box.
3. Undo the clamp that holds the large tubing to the air box using your pliers. Move the tubing away from the box.
4. Unclip hose attached to the back of the air box near the large hose (under it).
5. remove the small breather hose from the air box.
6. Pull air box up and out.
7. Remove snap on cover from top of battery.
8. Remove small snap on wiring cover from back of the battery covering.
9. Unbolt power steering reservoir (next to battery case).

10. Disconnect the battery cables. Positive side first.
11. Remove the 13 mm bolt at the base of the battery along with the hold down clamp.
12. Pull the top wiring away from the battery case and then slide the battery towards the engine.
13. Remove the plastic battery case.
14. Remove the battery

Posted on Oct 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vw polo 2006 dashboard rattling noise from the dashbody


the dash looks like it has loose parts at the back

Nov 28, 2013 | Cars & Trucks

1 Answer

Need help changing out the low beam on drivers side of 2006 buick rainier


Removal & Installation
Bulb Replacement
To Remove:

CAUTION
Halogen bulbs contain pressurized gas.
Mishandling a bulb may result in the bulb shattering into flying glass
fragments.

CAUTION
Make sure to wear eye protection when
handling a halogen bulb.

CAUTION
Do not touch the glass of a halogen bulb,
only handle the bulb by the base.

CAUTION
Do not allow a halogen bulb to come into
contact with dirt or moisture.

CAUTION
Make sure to dispose of a used halogen bulb
properly.

CAUTION
Do not allow children to handle halogen
bulbs.


  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket
    counterclockwise.

To Install:


  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket
    clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Headlamp Assembly
Chevrolet
To Remove:






Headlamp Assembly (Chevrolet)
gm-06-00-1591.gif




  1. Remove the grille from the front of the vehicle.
  2. Release the headlamp assembly retaining tabs.
  3. If equipped, disconnect the headlamp leveling motor connector.
  4. Disconnect the headlamp connector.
  5. Remove the park/turn and side marker bulb sockets from the headlamp
    assembly.
  6. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. Install the park/turn and side marker bulb sockets into the headlamp
    assembly.
  3. Connect the headlamp connector.
  4. If equipped, connect the headlamp leveling motor connector.
  5. Lock the headlamp assembly retaining tabs.
  6. Install the grille onto the front of the vehicle.

GMC, Oldsmobile, Buick, Isuzu, and Saab
To Remove:






Headlamp Assembly (GMC, Saab, Oldsmobile, and Buick)
gm-06-00-1590.gif




  1. Release the headlamp assembly retaining tabs.
  2. Disconnect the headlamp connector.
  3. Remove the park/turn bulb socket from the headlamp assembly.
  4. For GMC, Saab, Oldsmobile, and Isuzu vehicles, remove the side marker bulb
    socket from the headlamp assembly.
  5. Remove the headlamp assembly from the headlamp panel.

To Install:


  1. Place the headlamp assembly into the headlamp panel.
  2. For GMC, Saab, Oldsmobile, and Isuzu vehicles, install the side marker bulb
    socket into the headlamp assembly.
  3. Install the park/turn bulb socket into the headlamp assembly.
  4. Connect the headlamp connector.
  5. Lock the headlamp assembly retaining tabs.


prev.gif next.gif

Oct 28, 2010 | 2006 Buick Rainier

1 Answer

I need to know the step on how to replace headlight bulb on a 2006 vw beetle convertible


There are two spring clips located under the hood around each headlamp housing. Open both clips and extract the headlamp housing from the front of the car by pulling the plastic assembly by grabing the edges by the black rubber seal. The entire headlamp housing will pull out from the front bumper enough to allow you to change the bulbs. Repeat procedure and clip the spring clamps back in place.

Jun 21, 2010 | 2006 Volkswagen New Beetle

1 Answer

How do you change the headlight on a 2006 grand prix


  1. Raise the hood.
  2. Lift upward on the headlamp retainer (1).
  3. Pull the headlamp assembly outward enough to release the headlamp assembly from the upper fascia support.
  4. Position the headlamp assembly away from the vehicle body to access the electrical connector
    1. Disconnect the electrical connector from the headlamp assembly.
    2. Remove the headlamp assembly from the vehicle.
    3. Use caution handling halogen bulbs. Remove the headlamp bulb/socket from the headlamp, by turning counterclockwise. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    4. Remove the headlamp bulb/socket from the headlamp assembly.450a6d8.gif

May 06, 2010 | 2006 Pontiac Grand Prix

1 Answer

How do I get to the drivers side light bulb in a 2006 Chrysler Sebring Sedan? I have the replacement bulb and want to change it myself.


I will assume you are talking about the headlight?!

Removal
CAUTION: do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced life will result.

1) Disconnect and isolate negative battery cable.
2) Remove headlamp unit retaining screws. (bolts)
3) Remove headlamp unit to expose back of unit.
4) Disconnect wire connector from back of headlamp bulb.
5) Rotate retaining ring counterclockwise.
6) Remove retaining ring.
7) Pull headlamp bulb and remove from headlamp unit.

Installation

1) Install headlamp bulb to the headlamp unit.
2) Install headlamp bulb retaining ring.
3) Rotate retaining ring clockwise.
4) Connect wire connector to bulb.
5) Install headlamp unit.
6) Install headlamp retaining screws. (bolts)
7) Connect the battery negative cable.

More detailed info on how to get unit out.

Removal

1) Disconnect and isolate the battery negative cable.
2) Remove the two retaining screws.
3) Remove the upper fascia retainers by prying under the head of the fasteners with a flat bladed tool.
4) Remove headlamp unit from fender side first, then pull headlamp unit out.
5) Disconnect the wiring harness from the bulbs.
6) Remove the headlamp unit.

Installation

1) Connect wire harness to the bulbs.
2) Install headlamp unit.
3) Install the retaining screws.
4) Install upper fascia retainers.
5) Connect the battery negative cable.

I hope this will help you to get the light changed.

Jan 11, 2010 | 2006 Chrysler Sebring

1 Answer

57 reg vw polo n/s front mirror bulb replacement


Its ok i've decided to tackle this problem by myself as its not a priority @ this moment in time.

Jan 10, 2010 | 2007 Volkswagen Golf

1 Answer

I have 2006 Grand Prix How do I change head lamp?


Caution Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury:
Turn off the lamp switch and allow the bulb to cool before changing the bulb.
Leave the lamp switch OFF until the bulb change is complete. Always wear eye protection when changing a halogen bulb. Handle the bulb only by its base. Avoid touching the glass. Keep dirt and moisture off the bulb. Properly dispose of the used bulb. Keep halogen bulbs out of the reach of children.
Raise the hood.
Remove the headlamp assembly bolts from the upper fascia support.
Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support.
Position the headlamp assembly away from the vehicle body to access the electrical connector.
Disconnect the electrical connector from the headlamp assembly.
Remove the headlamp assembly from the vehicle.
Disconnect the electrical connector from the headlamp bulb/socket.
Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise.
Remove the headlamp bulb/socket from the headlamp assembly.

Jun 13, 2009 | 2006 Pontiac Grand Prix

1 Answer

06 polo headlamp (whole unit) bracket broken..???


whole unit,remove front bumper to get to bottom bolts

Jan 02, 2009 | 2006 Volkswagen GTI

2 Answers

Fog lights


A detent is a "stop". The manual is telling you to pull out the switch until it stops. The rear fog lamp on my VW Polo works the same way. It may help you to know that on my VW (1) although the headlamps will come on without the engine on, the fog lamp requires the engine to be running, (2) the headlamp switch must be in the "on" position before you can pull it out to the detent position.

Jul 28, 2008 | 1996 Volkswagen Cabrio

Not finding what you are looking for?
2006 Volkswagen Golf Logo

2,668 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...