Question about 1998 Audi A4

1 Answer

I have an Audi a4 and need to know how to turn off the passenger air bag. I have looked on the side panel by the passenger door and also in the glove box but there is nothing there. Any ideas ? The car is on a P plate.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My brake lights r not working the lighjt is always on could this because pads r low or is it a wiring issue changed fuses and bulbs audi quatra a 4

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the passenger side air bag sensors located on a 2009 chevy impala?


Side Impact Sensor (SIS)--Located behind door panel on the passenger front door
Front End Sensor--Located under the hood at the front right side of the vehicle
They have yellow wires going to them !

Jan 12, 2015 | 2009 Chevrolet Impala

1 Answer

Replacing airbags


Remove the negative cable from your car battery before replacing car air bags. Not removing the negative cable could deploy the replacement air bag, causing injury. More car obd2 scanner to maintain car with cheap price.
Deactivate the air bag by removing the air bag fuses. Look in your car owners manual to locate the fuses.
Unscrew steering column paneling and remove the airbag bolts on the back side of the steering wheel. Pull out the airbag until you see the back side and unplug the wires.
Plug the new airbag into the wires and rebolt it back onto the steering wheel. Replace the car steering column panels.
Replace passenger side air bags through the glove box or main dash panels. Remove the glove box by taking off the glove box straps and undoing the hinges. Unplug and unbolt the airbag, slide it out the front of the dash, slide the new air bag in and rewire and rebolt it.
Put the glove box or dash panels back together. Reconnect the fuses in the fuse panel and the negative cable on the car battery and you're finished.
OBD Tools 365 Days Shop

Jan 13, 2014 | 2003 Nissan Altima 3.5 SE

1 Answer

I have all the functions of the a/c and the associated operations of the dashboard doors when selected, except. no heat whatsoever when selected. The heater core is hot when the engine is @ normal temp....


Hi, this problem is caused by failure of the blend door actuator or structural failure of the door itself. First, access the actuator as instructed below. Have someone turn the key on and change the temperature setting while you watch the actuator. If the actuator turns, odds are the door hinge has failed. In this case, the heater box must be removed from the truck and split open to repair the door.
If the actuator does not move, it may have failed. Remove the actuator and check it for stripped gears or plug it back in and see if it will turn at all when the temperature control is changed. You might also want to check for voltage at the connector before buying a new actuator. A new actuator is about $40.


  1. Disarm the air bag system as explained below.
  2. Open the glove compartment to access the passenger air bag module bolts.

    jturcotte_2121.gif

    Fig. Passenger air bag module view

  3. Disconnect the passenger air bag module electrical connector
  4. Remove the two passenger air bag retaining bolts.
  5. Disconnect the passenger air bag module electrical connector.
  6. Placing one hand in the glove compartment, push the passenger air bag module out and remove it.
    WARNING Do not handle the passenger air bag module by grabbing the edges of the deployment doors.
  7. Remove the defroster opening grill.

jturcotte_2122.gif
  1. Fig. Defroster grill view


  2. Detach and position the RH demister hose aside.
  3. On vehicles with anti-theft/keyless entry, remove the screws and position the anti-theft/keyless entry module aside.
  4. Working through the opening near the RH defroster nozzle, remove the screw.
  5. Disconnect the electrical connector.
  6. Remove the screws and the temperature blend door actuator.
  7. To install, reverse the removal procedure. Tighten the air bag module bolts to 71 inch lbs. (8 Nm).

jturcotte_2123.gif

Fig. Temperature blend door actuator view




Disarming the Airbag System

  1. Turn all vehicle accessories OFF.
  2. Turn the ignition switch to OFF.
  3. At the smart junction box (SJB), located below the RH side of the instrument panel, remove the RH lower cowl trim panel and remove the restraints control module (RCM) fuse from the SJB. For additional information, refer to the Owner-s Manual.
  4. Turn the ignition ON and visually monitor the air bag indicator for at least 30 seconds. The air bag indicator will remain lit continuously (no flashing) if the correct RCM fuse has been removed. If the air bag indicator does not remain lit continuously, remove the correct RCM fuse before proceeding.
  5. Turn the ignition OFF.
    CAUTION To avoid accidental deployment and possible personal injury, the backup power supply must be depleted before repairing or replacing any front or side air bag supplemental restraint system (SRS) components and before servicing, replacing, adjusting or striking components near the front or side air bag sensors or RCM, such as doors, instrument panel, console, door latches, strikers, seats and hood latches.
  6. To deplete the backup power supply energy, disconnect the battery ground cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies (if equipped).
  7. Disconnect the battery ground cable (14301) and wait at least one minute.

Aug 23, 2011 | 2006 Ford Ranger

1 Answer

2004 Audi a4 1.8t air conditioner isn't working


Hi,the draining pipe is on that side it can be that its blocked just lift carpet and have a look where water is coming from

Jul 20, 2011 | 2004 Audi A4

1 Answer

Need to remove heater A/C dash control , what is proper procedure?


Look at fig. 4 for the heater a/c dash control: HEATER CORE Altima REMOVAL AND INSTALLATION
  1. Position the steering wheel in the straight-ahead position.
  2. Turn the ignition switch OFF.
  3. Disconnect the negative (() battery cable; then, the positive (+) battery cable. NOTE: Wait for a least 3 minutes after disconnecting the battery cables for the charge in the air bag circuit to dissipate before working on the air bag module(s).
  4. Remove the driver's side SRS and steering wheel by removing or disconnecting the following:
    • Lower lid from the steering wheel and disconnect the driver's air bag module connector
    • Left and right side lids from the steering wheel
    • Special bolts from both side of the steering wheel using a tamper resistant Torx wrench (T50)
    • Air bag module and store it face up
    • Horn's electrical connector and remove the steering wheel nut
    • Steering wheel from the steering column using a suitable puller
  5. Remove the passenger's side SRS by removing or disconnecting the following:
    • Glove box door and the glove box
    • Front passenger's air bag module connector
    • 2 special bolts using a tamper resistant Torx wrench (T50)
    • 4 passenger's air bag-to-instrument panel nuts
    • Front passenger's air bag module and store it face up.
  6. Drain the cooling system into a clean container for reuse.
  7. Discharge and recover the air conditioning system refrigerant.
  8. Working in the engine compartment, disconnect the heater hoses from the heater core tubes.
  9. Remove the instrument panel by removing or disconnecting the following:
    • Kick plate and dash side finisher on the driver's side
    • 2 lower panel-to-instrument panel screws and the lower panel on the driver's side
    • 2 lower reinforcement panel-to-instrument panel screws and the lower reinforcement panel
    • 6 steering column cover screws, the covers, the spiral cable and combination switch
    • 2 cluster lid "A" screws and the cluster lid "A"
    • 3 combination meter screws, disconnect the electrical harness connector and remove the combination meter
    • Switch panel
    • Instrument panel lower covers
    • Snap out the transmission shifter finisher (boot)
    • 4 cluster lid "C" screws and the cluster lid "C"
    • 4 audio and deck pocket-to-instrument panel screws and the audio and deck pocket
    • 5 center console screws and the center console
    • 2 center instrument panel screws and the center panel
    • front defroster grilles
    • Front pillar garnish
    • Instrument panel 3 nuts/4 screws and the instrument panel
    • 8 instrument stay assembly nuts and the stay
    • Steering member assembly 5 nuts/1 bolt and the steering member
  10. Remove the air conditioning housing assembly by removing or disconnecting the following:
    • Refrigerant lines from the air conditioning housing assembly
    • Thermo control amp
    • Air conditioning housing assembly
  11. Remove or disconnect the following:
    • Heater unit
    • Heater core from the heater unit Fig. 1: Exploded view of the steering wheel and air bag module 93112gd9.gif
      Fig. 2: Exploded view of the passenger's side air bag module 93112gd0.gif
      Fig. 3: Exploded view of the instrument panel assembly 93112ge1.gif
      Fig. 4: Exploded view of the heater housing assembly and related components 93112ge2.gif
      Fig. 5: View of the heater core and heater housing 93112ge3.gif
    To install:
  12. Install or connect the following:
    • Heater core to the heater unit
    • Heater unit
  13. Install the air conditioning housing assembly by installing or connecting the following:
    • Air conditioning housing assembly
    • Thermo control amp
    • Refrigerant lines to the air conditioning housing assembly
  14. Install the instrument panel by installing or connecting the following:
    • Steering member assembly and the steering member 5 nuts/1 bolt
    • Instrument stay assembly and the 8 stay nuts
    • Instrument panel and the instrument panel 3 nuts/4 screws
    • Front pillar garnish
    • Front defroster grilles
    • Center instrument panel and the 2 center panel screws
    • Center console and the 5 center console screws
    • Audio and deck pocket and the 4 audio and deck pocket-to-instrument panel screws
    • Cluster lid "C" and the 4 cluster lid "C" screws
    • Snap in the transmission shifter finisher (boot)
    • Instrument panel lower covers
    • Switch panel
    • Combination meter, connect the electrical harness connector and install the 3 combination meter screws
    • Cluster lid "A" and the 2 cluster lid "A" screw
    • Combination switch, the spiral cable, the covers and the 6 steering column cover screws
    • Lower reinforcement panel and the 2 lower reinforcement panel-to-instrument panel screws
    • Lower panel and the 2 lower panel-to-instrument panel screws, on the driver's side
    • Kick plate and dash side finisher, on the driver's side
  15. Working in the engine compartment, connect the heater hoses to the heater core tubes.
  16. Install the passenger's side SRS by installing or connecting the following:
    • Front passenger's air bag module
    • 4 passenger's air bag-to-instrument panel nuts
    • 2 new special bolts and torque using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm)
    • Front passenger's air bag module connector
    • Glove box door and the glove box
  17. Install the driver's side SRS and steering wheel by installing or connecting the following:
    • Steering wheel to the steering column
    • Steering wheel nut and torque the nut to 22-29 ft. lbs.
    • Horn's electrical connector
    • Air bag module
    • New special bolts to both sides of the steering wheel and torque the bolts using a tamper resistant Torx wrench (T50) to 11-18 ft. lbs. (15-25 Nm).
    • Both the left and right side lids to the steering wheel
    • Lower lid to the steering wheel and connect the driver's air bag module connector
  18. Refill the cooling system.
  19. Connect the positive (+) battery cable; then, the negative (() battery cable.
  20. Evacuate, charge and leak test the air conditioning system refrigerant.
  21. Operate the engine to normal operating temperatures; then, check the climate control operation and check for leaks.

Nov 19, 2010 | 2002 Nissan Sentra

1 Answer

Location of computor on 1995 merc villager


behind glove box

They seldom go bad so don't change until you know for sure. What are symptoms?

for villager/quest help go here

http://autos.groups.yahoo.com/group/villagerquest/
Powertrain Control Module (PCM) stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Refer to Module Servicing Precautions in Section 18-01 .
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the four console compartment plastic screws or C/D changer cover plastic screws (if equipped) and the console compartment door (045G36) or C/D changer cover.
  1. Remove the plastic screw, two lower screws, two center bolts, two upper screws and the screw at the instrument panel bracket, then separate the glove compartment from the instrument panel (04320). Disconnect the glove compartment striker plate catch electrical connector.
  2. Remove the two passenger side air bag module bracket nuts, the passenger side air bag module bracket bolt and the passenger side air bag module bracket.

  1. Remove the powertrain control module (PCM) electrical connector bolt. Pull the connector from the PCM and position aside.




    Remove the two PCM bolts.

    ec13884.gif

  2. Remove the PCM relay.

  3. Remove the three electrical connectors attached to the PCM.
  4. Remove the PCM from the instrument panel.

Mar 14, 2009 | 1995 Mercury Villager

2 Answers

Electrical fault Audi A4 2002


PRISE OUT THE TRIM PANEL AT THE BASE OF THE ARMREST WITH A FLAT-BLADED TOOL UNDO 2 SCREWS(DRIVERS DOOR) SINGLE SCREW ACCESSIBLE THOUGH THE ARMREST ON PASSENGER SIDE ,NOW GO TO THE BASE OF THE DOOR TRIM UNDO THE SCREW IN THE CENTRE,ONTO THE TOP TRIM NOW ABOVE THE RELEASE HANDLE,STARTING AT THE FRONT EDGE(DOOR HINGE SIDE) CAREFULLY PULL THE TRIM PANEL AWAY FROM THE DOOR TO RELEASE THE CLIPS,THEN SLIDE IT TO THE FRONT TO UNHOOK THE REAR EDGE OF THE TRIM PANEL,UNDO THE 4 SCREWS YOU CAN SEE,UNHOOK CABLE FROM REAR OF INTERIOR DOOR HANDLE,DISCONNECT WIRING PLUGS SPEAKER ,WINDOW MOTOR CONTROL UNIT AND THERE YOU HAVE IT ..EASY... IF YOU START NOW YOU WILL HAVE IT FINISHED IN 2 DAYS...ONLY JOKING....SHOULD TAKE 1 HOUR..HOPE THIS WILL BE OF SOME HELP TO YOU...LET ME KNOW HOW YOU GOT ON

Jan 25, 2009 | 2002 Audi A4

Not finding what you are looking for?
1998 Audi A4 Logo

155 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75197 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...