Question about 2001 Dodge Stratus

1 Answer

I dont know what sparkplugs to put in my car


Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 106 Answers

Just use the v power plugs and napa's best plugs and a cheep intake from auto zone it adds 7 horse alone

Posted on Nov 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need a spark plugs for my Suzuki aerio 2013

1763508us3 E3 #E368 or Champion Iridium # CHA 9201..OE IS IRIDIUM....USETO PUT THIS STUFF IN OWNERS BOOK.

E3 Brand
EEE E368

Apr 06, 2014 | 2003 Suzuki Aerio

1 Answer

I have a 2002 escape and out of nowhere it starts to misfire,, had the code pulled p0303 #3 cylinder misfire,, what to do next?? /33 is in th back i looked it up and have to take the intake off,,...

I would replace the sparkplugs and wires first which is more than likely the problem.The only thing left is the injector after that.And i would not think that you would have to take the intake off just to change plugs.Try to get to them from under neath

May 04, 2011 | 2001 Ford Escape

1 Answer

Check engine light was on with many codes, fixed all problems( all new exhaust, magnaflow cat system, flow master muffler, all o2 sensors were replaced, gave a tune up using MSD wires cap and rotor and e3...

new exhaust is to much for computer to figure out, since its flowing a lot more air , engine management cannot figure out fuel ratio hence the o2 sensor and knock sensor. u will have to install a performance chip or have computer re figured for new settings.

Apr 09, 2011 | 1996 Chevrolet Tahoe

1 Answer

I changed sparkplugs, and wires1yr ago,aprox.8000 mi. now i'm having a miss, it then showed a code po303 and po316 so i changed fuel filter ,pulled out the irridium sparkplugs i put last and put in new...

You either have a bad ignition module or a
vacuum leak,intake manifold,PCV Hose,etc
that effects cyl #3

Ohm Checking is for the 1980's

Todays tool is an oscilloscope, you won't
have at home.

Also Smoke the intake and EVAP System
for leaks (EVAP Smoke Machine)

Mar 26, 2011 | Ford Taurus Cars & Trucks

2 Answers

I have fire, gas, and no blown fuses. ive replaced distributor, cap, button, and coil and also replaced fuel pump. Im lost dont know what to do

Did you make sure you put the sparkplug wires back in the right holes?
If so it could be a compression problem. If you have the tool you can check it yourself by removeing the sparkplug one at a time and and put the gage in the empty sparkplug hole. Have some one turn over the motor and see if your compression is right. Do this to all the cylenders to be sure. If you dont have the tool, take it to a mechanic and have it checked. He can tell what it is and what it is suppose to be. Not knowing what engine you have, I can not tell you what compression to look for. If your compression is low, the rings are gone.

Feb 26, 2011 | Ford Probe Cars & Trucks

1 Answer

Need a picture of location of sparkplugs of 2002 lancer

Don't have a picture but I can tell you. They are located on the back end of the engine, pointing towards the windsheild. Mitsubishi made it hard for us. There are no wires, instead there a coils that are diamond shaped on top. Unscrew the one screw and just pull it straight out. You have to remove the top plastic silencer that is in line of your intake in order to do any of this.

Dec 07, 2010 | 2002 Mitsubishi Lancer

1 Answer

Ideal is normal when you are excelerating it is missing like its not getting enough fuel.spitting and sputtering.i just changed the spark plugs three days ago put E3 diamond fired plugs in her.but was...

i was wondering if you made sure that the gap on the plugs was correct for your vehicle it is different from car to car. I had that same problem of course mine was doing that right off the bat. so you never know. but again another possibility to check.

Sep 14, 2010 | Ford Ranger Cars & Trucks

1 Answer

Its the only sparkplug i have managed to find here in philippines that fits my engine, just wat to know if is suited for my car before i have to look abroad

get on the net to find out more,NGK, Nippondenso,or Bosch will be fine usually higher price better longer lasting plug,i dont think theres any major advantage

Apr 21, 2009 | Subaru Impreza WRX STi Cars & Trucks

1 Answer

1986 porsche 928 intake removal and replacement of sparkplugs.

You dont need to take off the intake manifold but the cold air intakes these unclip grab the convaluted tubing and pull it straight back out of the aircleaner then lift it up and un clip the bottom then pullit out of the intake snorkle

Mar 11, 2009 | 1987 Porsche 928

Not finding what you are looking for?
2001 Dodge Stratus Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides