Question about 2002 Hyundai Santa Fe

1 Answer

I need the number of the light bulb that is in the fog lamp switch on the dash.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Bad news. There are no part numbers for those little internal bulbs inside the fog light switch or even the rear defroster switch. Mine have blown out on my 04 Santa Fe. I've been through several dealers here in Denver and all tell me that Hyundai does not offer those bulbs individually. You must buy the whole switch. I know that sucks. I'm now checking with salvage yards to pull switches out of salvaged Santa Fe's. Hope this helps!

Posted on Feb 10, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fog lights wont work


Ryan, Does the fog light indicator on dash light up when you pull out the fog lamp switch? Also, Are you aware the fog lights won't work when high beam is on?

Mar 05, 2014 | 1999 Dodge Stratus

1 Answer

My fog lights won't turn on Nissan sentra GEX 2002


There are several things that can cause your fog lamps to not work. The fog lamp circuits need to be diagnosed. Your entire fog lamp circuit can be tested at the plug for the fog lamp relay located n the relay box.

PIN 5 on the relay should have battery power at all times. This power comes from Fuse #43 (15 Amp) in the fuse and fusible link box in the engine compartment. If there is power at this pin, the fuse and the circuit between the fuse and the relay is good.

PIN 3 on the relay goes to the fog lamp bulbs. There should be continuity to ground through the bulbs on this pin. If you have continuity to ground, connecting a jumper wire between PIN 5 and PIN 3 should make the fog lamps come on unless there is a short circuit to ground, which will cause Fuse #43 to blow. If there is no continuity to ground on this pin, the problem is either that BOTH fog lamp bulbs are burned out or there is a break in the wire between the relay and the bulbs.

PIN 1 Is the battery power for the primary coil in the relay. This power comes from the headlamp switch and power is only supposed to be present here when the headlamps are on and the dimmer switch is on LOW BEAM. If power is not present at this pin, the problem is a bad headlamp switch or an open circuit between the headlamp switch and the relay.

PIN 2 Is the control circuit for the primary relay coil. The control circuit should have continuity to ground when the fog lamp switch is set to the ON position. If there is no continuity to ground with the fog lamp switch on, the problem is a faulty fog lamp switch, an open between the relay and the fog lamp switch, or an open between the fog lamp switch and ground E37 (right front of engine compartment) and ground F7 (left rear of engine compartment) Please note: This circuit has redundant grounds....if one ground is not making good contact, the other ground can still make the circuit work.

PIN 4 on the relay is not used.

If all of the circuits/pins are working as described above, replace the relay.

That is pretty much it... That is all you really need to know to get your fog lamp circuits diagnosed. Let me know if you need further assistance.

May 13, 2012 | 2002 Nissan Sentra

1 Answer

Fog lamps on 2004 Tahoe won't come on.


You need to check the bulbs.These are known to go out a lot.Also you can check that you have power to the lights with a test light.Sounds like a bulb or wiring problem.I have had a few of these that are broken off because they are so close to the ground.Depending on if your four wheeling or in snow country.Hope this helps.Good luck.

Feb 16, 2012 | Chevrolet Tahoe Cars & Trucks

1 Answer

I HAVE a1997 Pontiac Bonneville the dash and foglights do'nt work and i know the fuss is good


You can check for power where it goes into the fog light switch and then the output terminal when the switch is on, or simply skip that step and turn the switch on and test for power at the fog lamp connectors if you have no power go back and check the switch if you do have power make sure the fog lamp housings are properly grounded and then test with a new bulb

Mar 04, 2011 | 1997 Pontiac Bonneville

1 Answer

99 gmc denali dash light, parking lights, tail lights, and dash light dont work. Interior lights, brake lights, blinkers, headlights work Turning on the headlight switch blows number 15 drl-fog fuse...


You have a short to ground somewhere in the drl-fog lamp circuit. Check for obvious wiring connector or wiring to drl & fog lamps. check wiring for pinched or broken wires coming from sockets. If you don't find problem, you can trace wiring from lamps to main harnesses and hopefully find source of short.
hope this helps.

Mar 02, 2010 | 1999 GMC Denali

2 Answers

How do you change the headlight bulb on 1996 olds delta 88? I cannot get to the bulb assembly.



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Disconnect the negative battery cable.
  2. Remove the fog lamp-to-bumper assembly retaining screws. Be careful not to disturb the adjusting screw.



0900c152800b1fa2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the 2 Torx® fog light retaining screws (1), making sure not to disturb the adjusting screw (2)
  1. Squeeze the bulb and socket assembly retaining clip prongs inward, and pull the bulb and socket from the rear of the fog lamp.



0900c152800b1fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Squeeze the bulb and socket retaining clip prongs inward ...


0900c152800b1fa4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: ... then pull the bulb from the rear of the fog lamp
  1. Unplug the fog lamp electrical connector.



0900c152800b1fa5.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Unfasten the fog lamp electrical connector
  1. Install the assembly, retaining bolts and connect the negative battery cable.


AIMING

  1. Park the car on a level surface, at least 25 ft. (7.6m) from a wall that is perpendicular to the ground surface. Make sure there is no excess weight in the trunk, unless you normally travel with that amount of weight in the car. Bounce the car a few times to settle the suspension.
  2. Measure and record the distance from the ground to the center of each fog light lens.
  3. Turn the fog lights on and adjust so the hot-spots (lit area of most concentrated intensity) are 4 in. (10cm) below the height of the lenses. The ADJUSTING screw is located at the top right corner of the fog light.

Jan 25, 2010 | 1996 Oldsmobile 88

1 Answer

1988 range rover - The brake light switch operates the brake lights but also: operating the brake light switch makes the fog lamp switch illumination bulb come on - if the fog light switch is already on...


Yep it happens
http://www.rangey.com/page7.html
Look for cutts in the wiring, tape up. Check all plugs and relays, you can find.
As for diagrammes, either a Haynes of down load a manual, if you have no joy on Google or Alltheweb try http://www.landroverweb.com/Land-Rover-Range-Rover-manual-pdf.htm
There are no front fogs fitted, only the driving lights in the air dam, the switch with the 2 on it lower front dash cluster with rear fog light switch etc.

Nov 15, 2009 | 1988 Land Rover Range Rover

1 Answer

Need a fuse box diagram to wire in fog lights


Fog lamps are installed on the front bumper. The switch is located to the left of the steering column on the dash panel. The fog lamps are turned off by the circuit relay when the high beam driving lamps are turned on. The circuit relay is located on the right front wheelhouse panel near the blower motor.

Good luck, and remember rated this help.
Removal & InstallationFog Lamp Element
See Figure 1
558610d.gif
Fig. 1: Exploded view of a fog lamp assembly

  1. Remove the lamp stone shields, the four bezel attaching screws, and the bezel.
  2. Remove the reflector assembly from the lamp body.
  3. Remove the bulb holder from the assembly. Remove the element from the bulb.

DO NOT handle elements with your bare hands, always handle with a clean cloth. Oil from your hands will cause the element to fail.
  1. Installation is the reverse of removal.

Fog Lamp Switch
The fog lamp switch is removed and installed by simply prying the switch from the instrument panel and unplugging the electrical connector.
FOGLAMP BEAM ADJUSTMENT

  1. Position the vehicle on a level surface, facing a wall approximately 25 feet away. Remove the lamp stone shields and loosen the adjustment nuts.
  2. Turn the fog lamps ON and adjust as follows:
    1. Distance between the light beam centers should be equal to the distance between the lamp assemblies on the bumper.
    2. Height of the light beams on the wall should be 4 inches less than the center of the lamp assemblies when mounted on the bumper.
  3. Install all previously removed items after turning OFF the fog lamps.

1995 Cherokee Chassis Schematic
8e08df0.gif

www.autozone.com

Aug 11, 2009 | 1995 Jeep Cherokee

1 Answer

Hyundai Sonata 2003 FOG LIGHTS DONT WORL


No.. power is supplied to both bulbs in parallell... when power is present at one, it's also present at the other. Clarification needed - have you checked to see if you have power (battery voltage) and ground at the fog lamp connectors?.. if so, the problem is the bulb(s) it/them/self/selves. If you have an ohm meter or a test light, it's a simple procedure. Check the bulbs with an ohm meter. Then using a test light (12 volt, make sure the test light bulb is good by connecting it to a charges 12 v battery) connect the test light bulb to each of the fog lamp connectors with the fog lamp sw turned on and the ignition key in the 'run' position. If the test light illuminates at both fog lamp connectors, then the problem is in the fog lamp bulb(s) themselves. If not, there's a wiring/control circuit problem. You can go to http://www.hmaservice.com/ and register and gain access to lots and lots of technical info about your Sonata.

May 26, 2009 | Hyundai Sonata Cars & Trucks

1 Answer

1st time install of OEM fog lights into a 1999 Mercury Cougar?


Look under the dash near where the headlamp switch mounts and if yours is equipped you should see I think it is a blue 4 pin connector with the following wire colors OG,OG/WH,OG/GN,BK.
This is for the fog lamp relay.If yours has this connector then you will need to purchase a relay ford part number F6RZ-14N089-AA should list for about $10.

Feb 25, 2009 | 2000 Mercury Cougar

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...