Question about 1997 Ford Explorer AWD

Open Question

I have a Ford Explorer XLT, 97 and need a diagram of a plastic multi tubed air intake that sits on the top of intake manifold, I need to remove it so I can get to thermostat plastic housig.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: 97 F150 4.2l Intake Manifold Bolts

the long bolts go to the inside or in the holes closest to the center of motor and the short ones go to the outside of the intake or closest to the valve covers

Posted on Jan 29, 2009

  • 17 Answers

SOURCE: intake manifold cover

remove oil cap steam an it should just lift off

Posted on Feb 23, 2009

  • 508 Answers

SOURCE: intake manifold leaking coolant at expansion tube nipple

It is pressed in. I usually just take the nipple out and run a threader into the hole and place a piece of threaded copper pipe into the newly tapped hole. The factory uses a thin steel tube and they rust out if the cooling system is not properly maintained.

Posted on Mar 16, 2009

  • 130 Answers

SOURCE: fuse box diagram

Here you go. Start on page 181.

http://www.motorcraftservice.com/pubs/content/~WOXEXP/~MUS~LEN/42/99expog1e.pdf

Posted on May 03, 2009

  • 111 Answers

SOURCE: Coolant tubes under intake manifold crack

I don't understand the question, anyway aluminum tube are not much better, electrolosis from disimilar metals in water jacket would take care of the aluminum in about the same timeframe, i would go stainless steel lines,

Posted on Feb 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2004 ford explorer xlt v6 4.0l gas. need a o2 sensor diagram. I need names and description. for example bank 1 sensor 2 after catalytic converter


https://www.google.com/search?q=1998+BMW+318i+Automatic+Torque+settings+Head+gasket&biw=1360&bih=650&tbm=isch&tbo=u&source=univ&sa=X&ved=0ahUKEwie8o3ix8_QAhUJRSYKHdIXBrkQsAQIKQ#tbm=isch&q=2004+ford+explorer+xlt+v6+engine+firing+order

Hope this helps

Bank two are the even cylinders. Follow exhaust manifold on the side. You will find an O2 sensor just after or on the manifold, before the catalytic converter. Then, look after the catalytic and you should find another O2 sensor, this is the one you mention in your post.

Nov 30, 2016 | 2004 Ford Explorer XLT

1 Answer

On a 2000 explorer 4.0 Soho do I have to remove the injectors to remove the lower intake


REMOVE UPER INTAKE 97 EXPLORER V6 4.0 - YouTube

? 12:22
https://www.youtube.com/watch?v=ugExJ0wkP8A
Jun 11, 2013 - Uploaded by Sum Guy
REMOVE UPER INTAKE 97 EXPLORER V6 4.0 ... I was told that all I have to do is remove the fan belt to get access to it ... FordExplorer 2000 intake manifold gasket upper lower P0174 by froggy - Duration: 36:54. by froggy 36,588 views ... Ford Explorer 4.0L SOHC Rough Idle P0171 P0174 Lean Codes ...

Putting the lower intake on my 1997 Ford Explorer 4.0 OHV ...

? 5:23
https://www.youtube.com/watch?v=qKE1vPxqPHs
Jun 27, 2010 - Uploaded by origionaldz
Putting the lower intake on my 1997 Ford Explorer 4.0 OHV sport .... I do have a 2000 5.0 ... @michaelheiland123654 To dothis job, you have to remove the alternator, unbolt the AC compressor, remove upper intake manifold, remove fuel rail,remove all injectors, ... Do you have the SOHC or OHV version?

1999 Ford Explorer 4.0L -need assistance on removing upper intake ...

www.automotiveforums.com > ... > Ford > Explorer ' Explorer Sport Trac
Sep 20, 2011 - 1999 Ford Explorer 4.0L -need assistance on removing upper intake ...Are you sure you have the OHV/pushrod engine and not the SOHC engine? ... Do youhave the upper intake manifold loose, you just are unable to ... the lower intake gasket, valve cover gaskets, Injector o-rings, plugs and wires. Thanks ...

How to replace upper intake manifold gaskets - Ford Explorer




Dec 09, 2015 | Cars & Trucks

1 Answer

How do you remove the fuel line from the intake manifold on a Ford Ranger XLT with a 2.9 Litre engine?


Not sure what you are saying that broke.
If the line is plastic and the fitting has no place for a wrench, you use a tool made to release the spring tension inside the connector. AC lines use the same setup.
If the plastic line is broke, you may be able to get a repair kit at your local auto parts store. The fuel line is designed to be replaced all in one piece, not repaired.

Nov 25, 2015 | Ford Cars & Trucks

2 Answers

Where is the air charge temp control sensor located on a 1999 ford explorer 4.0 sohc


Generally the Air charge temp sensor is in the intake tube between the air box & the intake. However, there is a possibility that it is part of the Mass air flow sensor.

Mar 08, 2015 | 1999 Ford Explorer

1 Answer

I need a diagram for a 99 explorer timing chain 4.0 4x4


it needs a special tool from ford the kit is 500 i think. used engine is cheap u can also put a 98 or 97 motor if its cheaper change the valve cover and intake also fly wheel exhaust manifold from the bad motor. i have done it works every time.

Dec 02, 2012 | Cars & Trucks

1 Answer

How replace intake gaskets focus 2000


SECTION 303-01B: Engine - 2.0L SPI 2000 Focus Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 07/5/2001 Intake Manifold
Special Tool(s) 412108.jpg Remover/Installer, hose clamp
412-108 (T96P-18539-A) Removal
  1. Release the fuel pressure. For additional information, refer to Section 310-00.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02.
  1. Detach the intake manifold bracket.
    • Loosen the nuts and remove the bolts.
    e0008065.jpg
  1. Lower the vehicle.
  1. Remove the air cleaner housing.
    1. Disconnect the mass air flow (MAF) sensor electrical connector.
    1. Disconnect the air cleaner outlet hose.
    • Remove the air cleaner housing from the rubber bushing.
    e0009092.jpg
  1. Disconnect the accelerator cable.
    1. Unhook the cable.
    1. Remove the plastic clip and position the accelerator cable to one side.
    e0009093.jpg
  1. Disconnect the speed control cable.
    1. Unhook the cable.
    1. Remove the plastic clip and position the speed control cable to one side.
    e0009094.jpg
  1. Disconnect the positive crankcase ventilation hoses.
    e0009794.jpg
  1. Disconnect the vacuum hoses.
    1. EVAP solenoid valve.
    1. Brake booster.
    1. Delta pressure feedback electronic (DPFE) system sensor.
    1. Exhaust gas recirculation (EGR) valve.
    e0009099.jpg
  1. Disconnect the EGR valve.
    • Discard the gasket.
    e0009351.jpg
  1. NOTE: Clamp the hoses to prevent coolant loss.
    Disconnect the coolant hoses from the intake manifold.
    e0024942.jpg
  1. Remove the vacuum hose assembly.
    e0009101.jpg
  1. Disconnect the throttle position (TP) sensor and the idle air control (IAC) valve.
    e0009353.jpg
  1. NOTE: Do not remove the oil level indicator tube.
    Remove the bolt and bracket from the oil level indicator tube.
    e0008058.jpg
  1. Remove the intake manifold upper support bracket.
    e0024943.jpg
  1. Disconnect the fuel injector electrical connectors.
    e0018167.jpg
  1. Disconnect the electrical connectors.
    1. Intake manifold runner control (IMRC).
    1. Camshaft position (CMP) sensor.
    1. Ignition Coil.
    e0024941.jpg
  1. Disconnect the fuel lines from the fuel rail. For additional information, refer to Section 310-00.
  1. Remove the intake manifold retainers and position the manifold to the rear of the engine compartment (shown with engine removed).
    e0009357.jpg
  1. Remove the IMRC manifolds (shown with engine removed).
    • Remove the two studs first.
    • Discard the gaskets.
    e0028869.jpg
  1. Remove the intake manifold from the engine compartment.
    e0028727.jpg

Mar 08, 2011 | 2000 Ford Focus

1 Answer

2004 ford 6cly rough idle must keep giving gas


V6? does it get any better when it warms up? Does RPM rev hi to low or does it sit at one speed and shakes? Hows the plugs? first thing first, buy a can of carb/choke cleaner $ 5.00 . Remove any plastic motor cover plates that would expose the motor. Spray cleaner around the base of the intake manifold and all mating areas of the intake manifold. ( not into the air intake) does the motor rpm change or rev up? if yes, you have bad intake gasket. also spray and check all air (vacuum) hose connections for proper fit and no cracks. Check plugs and note color and condition of each and what cylinder it was from, a brown paper bag color is normal, a super clean look is lean possible coolant leak, a burnt or melted electrode is early detonation timing, oil carbon deposit bad rings or valve guides,seals, wet is to rich , air fuel mix. Several things cause this, check all seals,air lines first,air filter, cracked or split intake tube, gasket check, does it run rough at cold idle only ( possible temp sensor ) you can check alot of things to eliminate without spending cash,

Jan 10, 2011 | Ford Taurus Cars & Trucks

2 Answers

Egr valve


Below is a link for instructions for the removal and installation of the EGR valve along with a diagram. Best of luck.
Greg
97 Buick EGR

Nov 04, 2009 | 1997 Buick LeSabre

1 Answer

99 explorer xlt v8


You have to remove the upper intake and it's at the rear of the pass. side valve cover.

Jun 10, 2008 | 1999 Ford Explorer

Not finding what you are looking for?
1997 Ford Explorer AWD Logo

Related Topics:

153 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...