Question about 1999 Jeep Grand Cherokee

1 Answer

My automatic transmission solenoid is causing check engine light to come on and locking transmission in 2nd gear. What needs to be done to replace the soleniod

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 35 Answers

Most transmission solenoids are located within the pan. If you replace the solenoids then it would be a good idea to change out the wiring harness that runs from the main transmission plug to the solenoids. Just lower the pan and drain it. Then, remove the one or two bolts that hold the solenoids in place. Replace the solenoids, wires, transmission filter and fluid at the same time (since you're already there). Make sure that you use a new pan gasket when you put the pan back on or it will leak fluid. Good Luck!

Posted on Nov 17, 2009

Testimonial: "very helpful"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

91 miata automatic transmission suddenly has only 2nd gear. Like limp-in mode. What could cause this?


shift solenoids or low /thin oil
when was the automatic last serviced
the engine check light should be on to read the stored fault codes

Apr 29, 2017 | Cars & Trucks

2 Answers

05 Trailblazer transmission says neutral but gear shiftier is locked in park.


Automatic Transmission Shift Lock Control System
The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
• The automatic transmission shift lock control solenoid
• The automatic transmission shift lock control switch
With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.

Circuit Description
The transmission range (TR) switch is part of the park/neutral position (PNP) and back-up lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The powertrain control module (PCM) supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.

These are all electronically controlled , yur best bet would be to take your vehicle to the dealer .

Apr 19, 2017 | 2005 Chevrolet TrailBlazer

2 Answers

This morning it started fine but will not come out of gear and my airbag light is on. Someone said it was the fuse but I am not sure which fuse. Any ideas ?


I am mechanic I really need to no more make ect. but it could be battery or the ignition switch or ignition lock n key but like I said need more information this is a guess that I told you

Oct 21, 2015 | 2008 Chevrolet Chevrolet TrailBlazer LT

1 Answer

Shifter is locked in park on a 2002 bravada that sayes on dash its in reverse


PRND321 Display
The instrument panel cluster (IPC) displays the selected gear position as determined by the engine control module (ECM). The IPC - instrument panel cluster receives a serial data message from the ECM indicating the gear position. The PRND321 display blanks if:
?€¢
The ECM detects a malfunction in the transmission range switch circuit.


?€¢
The IPC detects a loss of serial data communications with the ECM. The automatic transmission shift lock control system is a safety device that prevents an inadvertent shift out of PARK when the engine is running. The driver must press the brake pedal before moving the shift lever out of the PARK position. The system consists of the following components:
?€¢
The automatic transmission shift lock control solenoid


?€¢
The automatic transmission shift lock control switch

With the ignition in the ON position, voltage is supplied to automatic transmission shift lock control switch. Voltage flows through the normally closed contacts of the automatic transmission shift lock control switch to the automatic transmission shift lock control solenoid. The automatic transmission shift lock control solenoid is permanently grounded. This energizes the automatic transmission shift lock control solenoid causing the transmission shift lever to be physically locked in the PARK position. When the brake pedal is pressed the contacts in the automatic transmission shift lock control switch open, de-energizing the automatic transmission shift lock control solenoid. This allows the shift lever to be move out of the PARK position.
The transmission range (TR) switch is part of the park/neutral position (PNP) and backup lamp switch assembly, which is externally mounted on the transmission manual shaft. The TR switch contains four internal switches that indicate the transmission gear range selector lever position. The PCM supplies ignition voltage to each switch circuit. As the gear range selector lever is moved, the state of each switch may change, causing the circuit to open or close. An open circuit or switch indicates a high voltage signal. A closed circuit or switch indicates a low voltage signal. The PCM detects the selected gear range by deciphering the combination of the voltage signals. The PCM compares the actual voltage combination of the switch signals to a TR switch combination chart stored in memory.
You need a Tech2 scan tool to diagnose this problem ! possible range sensor !

Sep 03, 2015 | Cars & Trucks

1 Answer

2004 chevy impala solenoid stuck open


The solenoids are inside the transmission.
You may need a book and some special tools to make the repairs.

Jul 10, 2012 | Cars & Trucks

1 Answer

AUTOMATIC TRANS


on automatic transmissions Ok,1st check the transmission fluid level if low or if any at all, 2nd you might check your trans shift solenoids, or the wiring to the solenoids verify which solenoid you might need to replace by google it can show you a location of the 2nd and 3rd. If this doesn't cover the issue the next step is a tech to work on the transmission cause it could be and internal issue.

May 25, 2012 | 2003 Nissan Altima

1 Answer

P0732


This is caused by a sticking or defective 2nd gear electric shift solenoid.
P0732 NISSAN - 2nd. Gear Malfunction
Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Incorrect transmission shifting Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Jan 16, 2012 | Nissan Pathfinder Cars & Trucks

3 Answers

TRANSMISSION 2nd to 3rd GEAR HARDSHIFT


  1. the automatic transmission for bmw 328i 1997 move to front to rear

Jan 29, 2009 | 1997 BMW 328

1 Answer

1987 Toyota MR2, "Engine Still Lacks Power", (4AGE), Twin Cam, 1600 CC, 4 Cyl.


Sounds like you need gearbox oil (transmission oil in USA) .... check your levels and top it up.

Oct 31, 2008 | 1987 Toyota MR2

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

1,083 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...