Question about Ford E-350

1 Answer

MY 1996 E 350 VAN WONT START IT HAS A FULL CHARGE ON BATTERY ALSO BUT WONT EVEN ENGAGE THE STARTER

Posted by on

  • bomberchicks Nov 17, 2009

    would that be firewall mounted or starter mounted??

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 447 Answers

This van has the traditional starter selenoid. Not hard to replace, not expensive.

Posted on Nov 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

91 geo metro won't turn over, lights come on, starter doesnt engage


Hi Teresa thats ththhe sign of a battery going bad, how old is the battery? You might want to have it load tested so you can trouble shoot further, there could be more than 1 issue.

Dec 19, 2015 | 1991 Geo Metro

1 Answer

The girlfriend was riving my 2002 xterra. she said it run out of gas it now has about three gallons of gas, all the lights work, i can hear the fuel pump engage but the starter will not. I tried unhooking...


what do you mean by the starter will not. do you mean engage turn over or does it turn over and wont start because the fuel pump and starter have nothing in common. first of all what were your codes set and second if it turns over see if you can smell full and third if it doesn't engage at all she probally ran the battery down so try charging your batt or you can put a dvom meter on it and it should read 12.6 volts full charged 12.4 3/4 12.3 50% which will not start the car so if its any thing below 12.3 charge the batt . Tony ASE certified mechanic

Oct 31, 2013 | Nissan Xterra Cars & Trucks

1 Answer

Starter wont engage after replacing dead battery


Check power to starter motor solenoid, solenoid operation and starter motor voltage during cranking. If the starter motor is receiving power from the solenoid, but isn't cranking, then replace the starter motor.

Also check the condition of battery terminals, wiring and connections. Also check the earth wire from the body to the engine.

Nov 12, 2012 | Cars & Trucks

2 Answers

2005 jeep gc wont start. replaced fuel pump,replaced battery, run for two weekes, wont start but it click clicks


will it start with a jump? check battery for full charge, maybe alternator is not charging, check battery connections all the way down to starter, check selonoid by cross jumping terminals to engage starter.

Mar 09, 2011 | 2005 Jeep Grand Cherokee

1 Answer

2004 E150 van wont start. -5 degrees last night, battery is less than a year old and tests out OK according to NAPA test. When key is thrown, just a click is heard. Dash volt meter reads normal,...


START BY CLEANING THE BATTERY TERMINALS. NEG CABLE OFF FIRST THEN POSITIVE. CLEAN CABLES & TERMINALS PUT CABLES BACK ON & TIGHTEN POS. FIRST, NEGATIVE ON LAST & TIGHTEN. IF THAT DOESN'T DO IT. LOCATE STARTER RELAY ON FENDERWELL. TURN KEY TO START. MEASURE VOLTAGE AT STARTER RELAY. IT SHOULD READ NEAR 12 VOLTS. IF NOT CHECK NEUTRAL SAFETY SWITCH. THE STARTER MAY BE STUCK OR WORN AS A LAST RESORT HOLD IGNITION SWITCH IN START POSITION, AT THE SAME TIME TAP ON METAL PART OF STARTER WITH MEDIUM SIZE HAMMER. IF STARTER GOES AFTER HAMMER TEST, REPAIR OR REPLACE STARTER.

Jan 21, 2011 | 2004 Ford E150

2 Answers

Now it just will not start. It's was taking longer and longer to start. I tested the starter and replaced it. Now after a few (5-10 turns of the key) it turns over but wont engage and actually start. Even...


I would take the starter out and have it bench tested to verify if it has gone bad in the mean time.

Check the battery for bad connections and also for a full charge.

Check that the battery connections are clean and shiny and new looking when removed from the battery.

How old is the battery? 3 years is a typical life of most batteries sold and installed in cars these days. If unsure, then try a new one from the store which is fully charged to test, or connect a battery charger to your existing battery to see if it will take a charge.

Trickle charge your battery for up to 3 days to get a full charge on it.

Good luck on this repair.

Oct 29, 2010 | 1993 Subaru Legacy

1 Answer

2001 kia sephia car wont start just a ticking sound what is wrong


The ticking or clicking sound is coming from your Starter Solenoid because it is not getting enough Voltage from the Battery to engage the Starter Drive. It sounds like you have a dead Battery, try recharging your Battery first to see if it holds a full charge or check your Battery with a Volt Meter, when not running it should show at least 11.5-12.5 Volts, which would be enough power to start your car, any lower than that replace the Battery.

Aug 13, 2010 | 2001 Kia Sephia

2 Answers

How to start Mercedes C180 1999? Is it button start or key start?


i have a c180 merc petrol when starting the starter dosnt engage prop for afew turns then it engages and engine starts i have change the ring gear plus change the starter and still geting the same prob

Jun 28, 2009 | 1999 Mercedes-Benz C-Class

1 Answer

Wont start


Is starter engaging but is turning the engine slowly then not turning engine? (that's what I'm reading) If so, check both connections at the block and starter. If reading proper voltage 12v or better, check voltage across battery when in "start" if it drops below 9.5v the starter has failed. (you can turn the engine by hand...correct?)

Apr 25, 2009 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Ford E350 Passenger Van cranks but won't start


What year van is this? If later model, has anyone looked at the diagnostic code(s)? Could also be the Mass Airflow Sensor...

Feb 27, 2009 | Ford E-350 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...