Question about 1998 Toyota Camry

2 Answers

Heater only runs on high - 1998 Toyota Camry

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Master
  • 632 Answers

Replace your resistor block

Posted on Nov 17, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 534 Answers

Most likely caused by faulty blower fan speed control resistor module.
This unit is usually located in the heater air ducting under the dash ( in the blower fan airflow ) - unplug and remove fixing screws to replace.

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you install a heater core for a1991 Mazda Navajo


remove dash assembly try to back flush first or drain cooling system put water back in add cascade dish washing soap and drive a couple days if heater starts woreking better turn heat on high run engine open drain with a hose nozel on high and a large pan under drain flush all water out with engine running refill system with heat on high and vehicle running if heat still weak remove heater hoses the top should be the return line put a hose about 8 inces long on both out lets run the bottom hose to a high area where it can be suspended put a funnel in upper hose poor clr into hose until it comes out top of lower hose let set for hour and a half then flush out with water into a clear jug flush water vthrough upper hose then if u have air compressor have a 6 inch hose attatched to upper pipe and blow out core into same jug until the jug has clean and clear water refill cooling system and drive if heat doesnt work at first put engine under a load to release residule deposits in heater core and it should start flowing

Apr 01, 2012 | Cars & Trucks

1 Answer

MY HEATER, A/C BLOWER MOTOR ONLY WORKING ON HIGH?


You are probably going to need a blower resistor,High blower runs a seperate relay and the other speeds run through a resistor.Ussually located on the heater box under the dash.

Jan 30, 2011 | 1999 Chrysler Cirrus

2 Answers

My heater only works on high


If you mean the fan only runs on high speed, then you need to replace the heater blower resistor. It is usually located on the heater box, close to the blower motor.

Feb 24, 2010 | 1990 Pontiac Bonneville

1 Answer

1997 Chevy S10 pickup Fan switch for heater runs on high only.


replace the blower motor resistor located on the heater box were the blower motor is located the wiring to the blower may go to it. This is very easy to locate if you buy the part first.

Jan 06, 2010 | 1997 Chevrolet S-10 Pickup

2 Answers

Van is overheating and stays hot


first of all make sure that there is no air pockets left in the motor. these will cause an overheat right away.

the way to cure these is run engine with and radaitor funnel and once thermo opens, run the heater on high, this should take about 10 to 15 minutes.

WORST CASE SCENERIO:
You have a bad water pump!

Feb 17, 2009 | 2000 Plymouth Grand Voyager

1 Answer

Heater fan continues to run when heating system turned off.


Your Heater Power control module is bad I just had the same problem you can find it right behind the glove box it is mounted in the heater duct very easy to fix 2 screws and it is out and cost is about 150.00 at the dealer it is a dealer only part.

Dec 29, 2008 | 1996 Chrysler Town & Country

1 Answer

Heater motor only runs on high


Replace the heater blower resistor.

Dec 26, 2008 | 2002 Pontiac Grand Prix

1 Answer

1989 ford f350 a/c heater fan only runs on high, replaced switch ,didn,t help. thanks geo


When your heater only works on high it is usually
the resistor unit in the heater passage housing. Look for wires ( about 4or 5 wires ) attached to the
plastic heater housing under the dash. It should
have a screw or two holding it to the housing. Pull
it out and you will see several wire coils. If they are melted or broken then thats the problem. On any switch position except high the power goes through these resistors to slow the fan down. Good luck. Neil W.

Dec 08, 2008 | 1989 Ford F 350

2 Answers

Heater fan motor wont run on high


Check or have checked the blower motor resistor. This is usually how they act.

Oct 25, 2008 | 1995 Oldsmobile 88

Not finding what you are looking for?
1998 Toyota Camry Logo

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...