Question about 2005 Chrysler PT Cruiser

1 Answer

Need location of crankshaft sensor-PT Cruiser 2005

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chrysler Master
  • 632 Answers

It is located on the fire wall side of engine block just above the oil pan. Carefull as they tend to break in the block.

Posted on Nov 17, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change cam and crankshaft sensor for pt cruiser 2005 and still in the diagnostic problem cam sensor


just remove the battery terminals for a while firstly removing negative terminal

Sep 17, 2013 | 2005 Chrysler PT Cruiser

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

2 Answers

Where is crank sensor on 2005 PT Cruiser? It absolutely is not above the oil filter as on 01-03 PT's.


REMOVAL - 2.0, 2.4, 2.4L TURBO
The Crankshaft Position Sensor is in the front of the engine block just under the starter motor (CRANKSHAFT POSITION SENSOR LOCATION).

Disconnect the negative battery cable.
Raise vehicle and support.
On 2.4L SRT-4 remove the lower inner cooler hose from the metal tube.
Remove the Structural Collar (Structural Collar and Bending Strut-(Automatic Transaxle Equipped) ), refer to the Engine, Structural Collar Removal and Installation section.
Unlock and disconnect the electrical connector to the crankshaft position sensor.
Remove the crankshaft position sensor bolt.
Remove the sensor. Arrow points to sensor in picture.


emissionwiz_108.gif

Aug 22, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Were i the crankshaft position sensor located o a 2005 pt cruiser


near the oil filter.. above it...under exhaust manifold one small bolt holds it on. If the is a no start condition look for frayed wiring near crank sensor..... it has a harness that hangs too low on some of those. & rubs on cv shaft

Sep 14, 2010 | 2005 Chrysler PT Cruiser

1 Answer

Crankshaft position sensor replacement 2005 pt cruiser


it helps if you can lift or jack up the vehicle. be sure & use jack stands. it should be above oil filter on engine block under exhaust manifold. look for a sensor with one bolt holding it on. also check for frayed wires rubbing on cv shaft. sometimes all they need is fix one frayed wire

Sep 12, 2010 | 2005 Chrysler PT Cruiser

1 Answer

I have a 2008 pt cruiser. The engine light is on


mcdevito75 here, Yes a crankshaft sensor could cause your mentioned problems, the sensor should be located near the Harmonic balancer, you may need a special tool to remove it and if I'm not mistaken the new sensor thakes an adjustment, Have auto zone change this sensor for you, even if you succeed, how often will you change this sensor.

May 14, 2010 | 2005 Chrysler PT Cruiser

1 Answer

Where can I find the crankshaft position sensor on a 2005 Pt Cruiser Non turbo gasoline


IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Jul 14, 2009 | 2004 Chrysler PT Cruiser

1 Answer

Error code P0335 (2005 pt cruiser)


p0335 is crankshaft position sensor circuit fault code..possible just a faulty sensor,shouldn't set a circuit code if timing is off..a sensor is probably around a 100 bucks..located just above starter in block

May 18, 2009 | 2005 Chrysler PT Cruiser

1 Answer

Where is the crank sensor located on 2005 chrysler pt cruiser?


the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Dec 13, 2008 | 2005 Chrysler PT Cruiser

Not finding what you are looking for?
2005 Chrysler PT Cruiser Logo

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7711 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...