Question about 1994 Nissan Altima

1 Answer

The doorpannel speaker will not work on one but

The doorpannel speaker will not work on one but there is power going to

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 435 Answers

If you have access to the rear of radio, try reversing the channels, to see if the speaker works, and if it does, then you know the wiring to door speaker is ok, if it doesnt, then you know that the wiring is broken somewhere along the route. If you have access to the cable itself only, try using a AA battery, attach the cables to both ends of the battery, and if it makes a noise, then wiring is ok.

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

One speaker does not work power is going to white connector. Is there any way of opening the speaker to test wires going into speaker?


Just take the wire harness off the speaker and use a ohm-meter to test the resistance across the negative and positive terminals of the speaker. It should be about 3 - 6 ohms (if it's a little more that's fine). If the resistance is infinity (the needle or digital display doesn't move) the coil is shot and you should replace the speaker.

If for some reason the resistance is less than 2 ohms, I would also replace the speaker as there could be a short in the speaker coil somewhere. This could cause failure of the deck, due to short circuiting. Also, if the foam/rubber surround of the speaker is torn or has holes in it replace the speaker.

The thing to take away is: you are testing the speaker, with a meter, to see if it has fried its voice coil, and to make sure it looks OK mechanically by visual inspection.

Mar 20, 2016 | Cars & Trucks

1 Answer

Foor radio speakers won't work but there is power to speaker


check connection and test speaker with multi meter

Dec 21, 2013 | 2001 Nissan Maxima

1 Answer

I have power to my radio deck (which is after market) BUT none to the speakers, is there an amp in the 2001 pontiac aztek


The blue wire from your aftermarket radio that connects remote for a amp has to go to factory harness purple wire there is two purple wire so you need to try either or and it will work i just did one on an 2004 aztek

Jul 02, 2012 | 2001 Pontiac Aztek

1 Answer

I brought a rover mgzr and want to put radio in it but the wires in the loom have had the connectors cut off so i just got the speaker wires and the four wires to power the radio, I know which speaker...


My assumption would be black = earth, red/black = power, purple power antena? green white? start by getting a test lamp put the earth ********, turn ignition on & check all wires for power also test in acc position & off position in case 1 is memory (constant power) once you know which ones are power put the test light in the power & black to check the black is the earth. Once you have + & - & speakers it should work.

Jun 27, 2012 | Cars & Trucks

1 Answer

Speaker wiring problems in 99 chevy malibu


Somethings loose. Check the plug on the back. You may have to take it partially out to do so!

Apr 19, 2017 | 1999 Chevrolet Malibu

1 Answer

I got a 2001 chevy blazer, i was hooking up speaker and i turned it down to call my friend on the phone and i go to turn itback up it makes a few thumps and stops working what could this be??


Try reversing the wires on the speaker. If it still doesn't work, it has blown out already. Either you have to many watts going to it (only run 75% of capable power or 75w to a 100w speaker) or you got a bad one and they usually blame it on to many watts.

Feb 26, 2011 | Chevrolet Blazer Cars & Trucks

3 Answers

Changed Radio - now speakers don't work. I took out the Chrysler radio that had a CD and cassette in it and replaced it with an aftermarket radio. Now the speakers don't work. I got the adapter from a...


Sounds like your Gr Caravan has the premium sound package. You likely haven't hurt anything - but you may need to modify the wiring a bit. The speakers have a tweeter speaker in the center of the main speaker and the wiring goes through that. However, it only worked with the premium package. Go in to the speakers and move the wiring connections from the tweeter to the main speaker. Your other option is to replace the speakers.

Jan 19, 2010 | 1994 Dodge Grand Caravan

2 Answers

Radio gets no power, fuses and wires are good


Check your connections again. Check that they're connected correctly. Look at a diagram, check the fuse on the power (red) wire from the radio. The radio might have fuses on the back of it, check them too. If anything put and tape every thing back together and use a harness then go from there.

May 07, 2009 | 1998 Honda Accord

2 Answers

Good Morning, i have a 05 Cadillac STS and I can't open my drivers side door via the handle, I have to use my key to open it.


sorry more complicated than that good thing is that it can be done had same prob and fixed by myself
it is due to a two prong sensor behind the handle that corrods over u need to order a new handle assembly about $70 on gm parts direct good site for parts u need to remove the doorpannel and then the handle from the outsided once you remove the pannle there will be a screw on side of door fto loosen handle then remove and replace follow steps to restore everything to its original...hope this helps

Jan 13, 2009 | Cadillac STS Cars & Trucks

Not finding what you are looking for?
1994 Nissan Altima Logo

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...