Question about 2000 Chevrolet Cavalier

2 Answers

Ive striped a lug nut off broke lug nut pin or bolt what can i do?

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 108 Answers

Take it to a local shop and they will have to spend about a hour of labor etc. but they will be able to take off the hub. and use a press to remove the stripped broke off lug. then they will be able to press in a new one. It shouldn't take that long or be that much cost, this is something which does happen at shops quite often and most local repair shops will have the tools and new lugs for resetting.

Posted on Nov 16, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

Drive it out and press a new one in,its easy if you have a z clamp you did not say if it is drum or disk brake, but still it easy to do good luck And I hope this helps you

Posted on Nov 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 cadillac fleetwood i removed the bolt the pin and the c clip but shaft still wont come out. How do i remove it?


Be sure the bolts on the backing plate are removed and then put a slide hammer on the lug nuts and pull the bearing out, it is on the end of the shaft in the hub just behind the lug nuts.

Apr 10, 2016 | 1993 Cadillac Fleetwood

1 Answer

How to change rear ball joints on 2002 dodge stratus


Instructions
  1. Remove the Upper Control Arm
    • 1Disconnect the ground battery cable using a wrench.
    • Loosen the front wheel lugs located on the same side of the upper ball joint you need to replace. Use a lug wrench.
    • Raise that same front wheel off the ground using a floor jack and support the vehicle on a jack stand.
    • Finish removing the tire.
    • Take the cotter pin off the upper ball joint stud holding the steering knuckle arm. Use a pair of nose pliers.
    • Remove the castle nut from the upper ball joint stud using a wrench or ratchet, ratchet extension and deep socket.
    • Loosen the two bolts securing the back of the upper control arm to the mounting bracket. Use a wrench to hold the bolt head as you loosen the retaining nut with a ratchet and socket.
    • Pull the control-arm ball joint off the steering knuckle arm. You may need to use a Pitman arm puller to free the ball joint.
    • Finish removing the two bolts from the back of the upper control arm and lift the upper control arm off the vehicle.
    Install the New Upper Control Arm
    • Set the new upper control arm in place and install the two bolts and retaining nuts to secure the back of the upper control arm to the mounting bracket. Remember the bolt heads should point inward toward the shock absorber with the retaining nuts on the outside of the mounting bracket. Do not tighten the bolts yet.
    • 11Insert the control-arm ball joint on the steering knuckle arm and start the castle nut with your hand over the ball joint stud. Do not tighten the nut yet.
    • Tighten the two bolts on the mounting bracket to 67-foot lbs. (91 Nm) using a torque wrench. Hold the bolts with a backup wrench as you tighten the retaining nuts with the torque wrench.
    • Tighten the ball-joint castle nut to 45-foot lbs. (61 Nm) using the torque wrench, ratchet extension and deep socket.
    • Install a new cotter pin through the joint-ball stud hole using the nose pliers. If necessary, tighten the castle nut just a few degrees to clear the stud hole through one of the castle nut slots.
    • Mount the tire on the wheel assembly and install the wheel lugs using the lug wrench.
    • Lower the vehicle and finish tightening the wheel lugs.

May 31, 2012 | Dodge Stratus Cars & Trucks

1 Answer

What is the part that holds the lug bolts called


just go to your local parts store and tell them what you need and they will get you what you need to replace them and you can do this in less than one hour

Dec 26, 2011 | 1996 Ford Windstar

1 Answer

The lug bolt broke when i removed the nut. to fix the brakes. how do i get the lug bolt out?


jUST TAKE ALL THE LUGS NUTS OFF & REMOVE ROTOR WITH A 5 LLB SLEDGE HAMMER KNO0CK BROKEN BOLT & REPLACE WITH NEW BOLT

Jun 16, 2011 | 1999 Daewoo Leganza

1 Answer

The bolt broke off with the lug nut. how to take out the old bolt.


If it is like a VW Jetta lug bolt, soak it with PB Blaster.
Take a sharp center punch and a heavy ball pien hammer and drive the broken threaded portion the bolt in the direction it goes to remove the bolt. Hold the center punch at appor 60 degree angle to the plane of the drum or disk and hammer away.
If it is a splined threaded bolt soak it with PB Blaster and drive it out from the back side of the drum or disc. Use a pin punch or rod or old bolt slightly smaller then the splined broken off portion and hammer away.

Above proccdure saves my bacon countless times!
Good luck
Terry

Sep 19, 2010 | 1985 Toyota Tercel

2 Answers

I have a 91 honda accord ex, one of the front lug


If you undid the hub nut and retainer ring with clip it should tap off once brake caliper is removed.

May 15, 2010 | 1991 Honda Accord

3 Answers

Removing Lug bolt plate from car


HI:
Stop!!! The "round plate" that the wheel studs are mounted to is your hub assembly. To replace a broken stud, you simply need to use a hammer and a drift pin punch, and pound it backwards. You replace it in similar fashion: insert the new wheel stud in from the back side of the hub, and use the wheel lug nut to draw the new stud into the hub assembly.

Mar 26, 2010 | 2006 Hyundai Elantra

1 Answer

2 wheel bolts are striped. Our wheel is held on


the old ones will remove by slamming a good wack to it. installation is done by threading the lug nut on to press it on

Feb 20, 2010 | 2001 Chevrolet Blazer

3 Answers

I have sheared a front wheel lug on my 1995 landcruiser Amazon. Friends had a puncture and didn,t tighten wheel nuts properly on spare. How do I replace.


The lug nuts are press fitted in the rotor. You should be able to hit the bolt with a hammer(or hammer and punch if the bolt is sheered flush with the rotor) and it should come out.

Jan 17, 2010 | 1995 Toyota Land Cruiser

Not finding what you are looking for?
2000 Chevrolet Cavalier Logo

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...