Question about 1993 Dodge Dakota

1 Answer

1993 dodge dakota 4*4 codes are in order as

1993 dodge dakota 4*4 V-8 trouble codes are in order as the engine light lit up on the dash
12
27
15
55 any idea I have a intermittant miss that sets the eninge light when it happens, secdondary ignition has been replaced

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 437 Answers

12= Standby memory power lost
27= PCM to injector failure
15 = No VSS reference
55 = Completion of fault code display

With the given codes and the way it is running I would say that you are having either a issue with the PCM ground and or the main connector to the PCM. Intermittent failure in the plug would cause these cascade codes with a misfire.

I would inspect the plug and make sure there is a good verifiable ground from the cab to the frame even to the transmission itself. The cabs of these trucks have notoriously bad grounding. Best to establish a new one rather than chase the old one and assume it is ok. Small gauge wire with terminals will suffice.

You may also be noticing that the volt and temp gauges go up and down slightly with the turn signal when it is activated? Radio may also freak out at louder volume settings if the ground in the cab is compromised.

Posted on Jan 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1993 dodge dakota with a 3.9L V-6. My question is what do i need to do when the trouble shoot code 41 shows up which means the generator field isn't switching properly?


Chrysler Fault Code 41: Alternator field control circuit open ...

www.allpar.com/fix/codes/faults/code-41.html
Possible reasons for Chrysler fault code 41: Alternator field control circuit open or shorted. ... allpar, the Chrysler - Dodge - Plymouth - Jeep site. Note: Allpar ... FauxPar: Return of the Barracuda, 1987-1996 Dodge Dakota pickup trucks, Pinner: ...

Aug 11, 2015 | 1993 Dodge Dakota

1 Answer

How do you get the computer trouble codes


On a dodge all you have to do is turn the key off and back on again 3 times. The codes will show on your dash.,

May 30, 2014 | 1993 Dodge Dakota

1 Answer

I need diagram of firring orde for dodge dakota 3.9 six cilynders


3.9L V6 engine firing order is 1-6-5-4-3-2, cylinders on the pass side front to back are 2-4-6, cylinders on the driver side front to back are 1-3-5.

May 14, 2012 | 1993 Dodge Dakota

1 Answer

1993 dodge dakota 5.2 v-8, under light throttle it as a surge. Engine rpm's will go up and down a little.


start by cleaning the throttle bore and plate with spray carb cleaner. use a toothbrush and rags to clean it out well. Then clean the IAC valve and its bore. lastly replace the PCV valve. use the rest of the carb cleaner to find any vacuum leaks at hoses and fittings. If problem is still there test or replace TPS.

Check your computer for trouble codes.

Nov 09, 2010 | 1993 Dodge Dakota

1 Answer

2002 dodge dakota engine misfire and service engine light on


if you correct the miss the trans will shift correctly, the engine miss set a trouble code, that will ID the cylinder that is missing, have the trouble codes tested

Aug 24, 2009 | 2002 Dodge Dakota Club Cab

1 Answer

Check engine code


I'm new to this website, have a problem with my '93 Dakota, 5.2L but thought I'd post to your question.

The readers would need more information than what you supplied.

On my Dakota, to check the CEL(Check Engine Light), cycle the ignition switch to RUN-OFF-RUN-OFF-RUN, then count the flashes of the CEL. There will be a distinct pause between each set of 2 number flashes, finally ending with a code of 55 signaling the end of the code display.

Some of the codes will keep the CEL lit all the time, while others will store but not light the CEL when running.
If you post the codes you see, and look them up, it might give you (and the reaers here) a better idea of your problem.

Aug 01, 2008 | 1993 Dodge Dakota

Not finding what you are looking for?

Open Questions:

See all 1993 Dodge Dakota Questions

1993 Dodge Dakota Logo

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...