Question about 1994 Isuzu Rodeo

1 Answer

I have 2 questions 1st is my check engine light illuminates solid after about 1/2 hour at speed 55-60 wont do it just in town driving after it has come on and i come to a stop it will re illuminate after the engine get to 1000 rpm. The 2nd is what cause the vehicals to make that puttering noise is i just part of them getting older? gi_joe_steve@yahoo.com

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 5,568 Answers

If you are in the US, call your nearest chain auto parts store and ask if they do free scans of your on-board computer; most do. The source of your problems is probably stored in your system.

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Auto trans shifter shifts p-r-n-d-2-1 it wont shift out of 1st .. sat for 8 months i drove it 50 miles 5 days a week for 9 years serviced reg. never any troubles before i started it i changed oil filter...


There must have been a 'Check Engine' Light? When a 'check engine light' (MIL=Malfunction Indicator Lamp) is turned on, there is a DTC (Diagnostic Trouble Code) set/stored in the ECM/PCM (Engine Control Module/Powertrain Control Module). This code identifies which engine management system component/function experienced a malfunction. Once you pull/read this code, you may begin diagnosis. You'll need an OBDII (On-Board Diagnostics II) code reader. You should find a P07?? number stored (P07??... is a transmission code).

Aug 31, 2011 | 2000 Hyundai Elantra

3 Answers

An orange warning light shaped like an engine has come on what does it mean


Engine warning light

eng_man_light_72.jpg Illuminates when the ignition is switched on. It should extinguish as soon as the engine starts.
If it illuminates with the engine running, it indicates a malfunction with the engine management system. Have this checked as soon as possible.
If it flashes when driving, reduce the vehicle speed immediately until the light illuminates constantly. If it continues to flash, avoid heavy acceleration and high engine speed, stop the vehicle and have it checked immediately.
On some vehicles this light may be red - again stop the vehicle and seek assistance.
If it is safe to do so, try stopping the vehicle, switching off the engine, wait two minutes, then restarting the engine to reset the engine management system.
With the light illuminated, the vehicle is still safe to drive as long as no other faults are apparent with the engine. Have the vehicle checked by a dealer or garage as soon as possible to avoid any damage being caused to the catalytic converter

Jun 09, 2011 | 2007 Isuzu MU-7

1 Answer

Truck is stranded with a faulty PCM


If your light has not come on, it means one of two things. 1) you have blown a fuse for the PCM, and need to replace it. 2) you drove your vehicle around with a bad PCM, and it finally quit all together. If it is not the fuse, you are pretty much stuck. Why would you drive it with a bad PCM?

Jul 11, 2009 | 1994 Jeep Grand Cherokee

2 Answers

High rpm's and not going fast


the very 1st thing u do is have the system tested for the trouble code that is stored whenever the check eng light comes on, but most likely u need a transmission speed sensor, u have lost Over Drive by the sound of it.

Jul 02, 2009 | 2000 Chrysler Town & Country

1 Answer

Gauge light on?


Gauge light illuminates when the ignition is switched on. It should extinguish as soon as the engine starts.
If it illuminates with the engine running, it indicates a malfunction with the engine management system. Have this checked as soon as possible.
If it flashes when driving, reduce the vehicle speed immediately until the light illuminates constantly. If it continues to flash, avoid heavy acceleration and high engine speed, stop the vehicle and have it checked immediately.
On some vehicles this light may be red – again stop the vehicle and seek assistance.
If it is safe to do so, try stopping the vehicle, switching off the engine, wait two minutes, then restarting the engine to reset the engine management system.
With the light illuminated, the vehicle is still safe to drive as long as no other faults are apparent with the engine. Have the vehicle checked by a dealer or garage as soon as possible to avoid any damage being caused to the catalytic converter.

Jun 24, 2009 | 1998 Toyota Corolla

1 Answer

My 2002 Hyundai Elantra Gt (2.0L)engine runs rough during low speed acceleration, but runs fine at highway speeds. I have changed fuel filter and spark plugs, but after engine is warm it still misfires...


The Hyundai online shop manual and my newly arrived Hyundai shop manual kept pointing to the coil as a possible problem. While preparing to check coil continuity I discovered the pigtail connected to the bottom of one of the coils was loose and the contacts were burned. This is the coil that supplies spark to plugs 1 & 4, the same ones that kept showing up each time the check engine light illuminated. After cleaning the contacts and making sure the pigtail was securely attached to the base of the coil I have had no further problems.

Jun 11, 2009 | Hyundai Motor 2002 Elantra

1 Answer

Hot transmission wont engage back into 1st


these transmissions had a problem with the piston in the trans cracking. when the fluid is cold and thicker it is ok, but when it gets hot and thin it cant hold the pressure and the clutch doesnt engage

Apr 17, 2009 | 1994 Lincoln Town Car

2 Answers

2005 Chevy Impala speedometer


Replace the speed sensor, but also make sure you clear any codes, even if none are showing up, disconnect the battery for about 1 hour. After that drive it easy for a while, so it can relearn.

Jan 06, 2009 | 2005 Chevrolet Impala

Not finding what you are looking for?
1994 Isuzu Rodeo Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...