Question about 2002 Pontiac Montana

1 Answer

How hard is it to change the front hubs? and are there any diagrams online?

Posted by on

  • drnow May 11, 2010

    by hubs, whae exactly do you mean?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 127 Answers

There should be 4 bolts on back side of the hubs, take thoughs off and tap it out with a hammer. before you do that make sure you remove calipor and rotor.

Posted on Nov 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We need a picture of a Front wheel bearing hub assembly or diagram


DUDE, GO TO AUTOZONE.....GET THE SHOP MANUAL...BUY IT, LOOK AT IT.....OR HAVE THE AUTOZONE PEOPLE PRINT YOU A DIAGRAM OF THE FRONT HUB ASSY.

Jul 29, 2014 | 1996 Ford F150 Regular Cab

1 Answer

Wheel hub assembly diagram


Go to you tube and ask for "How to replace Dodge Dakota front hub", you will find 2 or 3 good videos about it, I follow these videos and change mine in about 3 hours, note that I never did it in any car or truck. Another tip is that all videos I found was about 4x4 Dakotas and mine is 4x2, the only difference is the hub center fix, 28 mm screw on 4x2 and 32 mm nut on 4x4.

Apr 22, 2014 | 1989 Dodge Dakota 2WD

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

I need a diagram of the front hub assembley for a TF maga


Most likely(99%) you have pressed in bearing in to the hub, sience it's front wheel drive car.

May 03, 2010 | 1996 Mitsubishi Eclipse

1 Answer

I am looking for front bearing assembly diagram for a S10 Blazer (1995)


well these are 1 pc units on 4wd models they are sealed
hubs and the only way to change the bearing is buy a new hub assembly

Sep 26, 2009 | 1995 Chevrolet S-10 CA Edition

3 Answers

How to change front wheel bearing ford focus


You can do it yourself just take your time:
To change front wheel bearing.
1. Jack car up support with jack stands
2. take tire off
3. take caliper and brakes off
4. take rotor off
5. unbolt axle shaft nut at bearing hub
6. use a 3 lb slug with a block of wood
7. place wood on axle shaft and knock it in
8. back side 3 10mm bolts unbolt
9. front side have to pry off bearing hub Assembly only beacuse has dirt in knuckle hole.
10. clean hub knuckle and reinstall.
Its really not that hard or you could have them done for $900 and up. (I have changed alot of wheel bearing assemblies )Whats your e-mail I can send you a diagram if you want.

May 01, 2009 | 2004 Ford Focus

2 Answers

Broken wheel studs on 1996 grand am se- passenger front


usually they are an assembly but when i get crazy and damage studs i raise and support both front wheels so i can turn them and slowly move the hub where you can fit teh stud in and use an open lugnut to tighten down it will pull the stud in (i use an air compressor for this)

Apr 28, 2009 | 1996 Pontiac Grand Am

1 Answer

How to change the front wheel hub for 2000 LINCOLN LS


the whole spindle needs to come off unless you have the correct pullers here is a diagram have a good day DB
101414664

Feb 15, 2009 | 2001 Honda Civic

2 Answers

1989 4X4 SUBURBAN FRONT ROTORS


I have had a similar problem on my 82 Jimmy when I wanted to replace my 6 lugs (bolts) on the wheel. I guess, you have to remove the hubs to bring out the rotors. I myself searched on the net for a detailed pic, but did not succeed. I however saw my mechanic do it on mine. You need to carefully remove the pins, sleeves, springs etc. in the hub. Some clippings / locks / pins might seem hard to take out, but little inspection would make it easier. Some special tools such as a pointed tip plier might be required to release certain pins.

Anyway, best of luck :-)


By the way, I am having problems with my 4X4 lately. I got the lugs changed and the mechanic seems to have mis installed the hubs. Now I sometimes have a grinding sound underneath, a couple of times (even when 2 wheeling and hubs released), Today the wheels did not lock and I could not get out of sand. To my embarrassment, a land cruiser had to pull me out. Can some one help ?

Nov 14, 2008 | 1989 GMC Suburban

Not finding what you are looking for?
2002 Pontiac Montana Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...