Question about 1966 Ford Mustang

1 Answer

Need help with wiring from the dash to the dist and coil . the wires have been cut and i can't seem to get the right combination.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,002 Answers

Check out faxonautoliterature. They carry the original Ford service manual for your Mustang. You can get the book for $69 or a CD-Rom for $49. They also show a wiring diagram for it for $8. I've used them before and found their service to be excellent. Hope this helps.

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hello, I have a 02 GMC Sierra 4.3L v6. The problem I'm having is that the truck cranks over but no spark. I've changed the ICM, ignition coil, have pulse on the wire from the crankshaft sensor an all other...


There will b a senser under cap.and one on coil u should be able to have tested at any auto parts store..if not ....u should have codes in memory have it scaned

Jan 04, 2015 | Cars & Trucks

1 Answer

Engine won't start. Getting no spark.


Have you check to see if the timing on the car is right?

Nov 08, 2013 | Cars & Trucks

1 Answer

Trying to figure out what the name of a part is


That would be the ignition coil, the part that creates spark at the spark plug. If you follow the electrical path from the coil wire to the distributor cap, and from there, the spinning rotor just under the distributor cap carries the path from the coil wire at the cap's center to the spark plug wires around the dist. cap, and through the plug wire to the spark plug.
The high voltage causing the spark is created in the ignition coil by the engine computer at the precise right moment signaling an ignition module to cut 12 volts current to the ignition coil. This causes the coil to internally build up high voltage which is passed through the coil to distributor cap wire. The computer knows the precise right moment to initiate spark from engine sensors, primarily the crank position sensor and the cam position sensor.

Nov 06, 2012 | 1999 Dodge Durango

1 Answer

DIST WIRING 1.6 88 TOYOTA COROLLA


what about coil? check whether you have or not spark from coil to distributor,or from distributor to spark plugs.

Aug 16, 2012 | Cars & Trucks

2 Answers

Car cuts out after it warms up..runs fine cold


age is showing cause some electric is heatng up-a relay--solenoid--switch etc--you need a diagnostic test-1st a scan then maybe inspection of wiring with instruments--------make sure uve done a tuneup-new dist cap and plug wires

May 31, 2011 | 1994 Buick Century

2 Answers

My toyota corolla was idline fine then just cut off . no spark in distributor


If your engine cranks normally but will not start and cuts off because it has no spark, or it stalls and won't restart because it has no spark, the problem may be due to any of the following:
A bad pickup inside the distributor a stripped distributor drive gear (common problem with plastic distributor drive gears, broken, loose or corroded wires from the pickup to the ignition module or PCM.
If there is power going from the coil to the dist, but no spark coming out of the dist. the Condenser is bad. Small round thing that has a wire that hooks to the points. If the engine has no spark, check for voltage at the coil positive terminal when the ignition key is on.
If there is voltage, the problem is on the trigger side of the coil (pickup, crank sensor, ignition module or primary wiring circuit).
If there is NO voltage at the coil, the problem is on the supply side (the ignition switch or ignition wiring circuit).
If the coil has voltage, the problem may be a bad high voltage output wire from the coil to the distributor, hairline cracks in the coil output tower, or cracks or carbon tracks inside the distributor cap or on the rotor.You can check this with voltmeter.------------------
That's it.

Nov 18, 2010 | 1990 Toyota Corolla

1 Answer

86 gmc 2wd 305 slight cam. At initial start, engined fired and ran great for about 30 min or so at operating temp, then started stumbling and will no longer start. Spark was present at only 5kw though, not...


This works with the 5 prong module on an HEI ignition system with the coil that is mounted on the top of dist. The wires that come out of the back of the dist go to a spark controll module under the dash and they are junk. There is a conector on the wiring harness about 5" from the dist unplug that conector and run a jumper wire from the green wire to the black wire on the dist side and make sure you tape up all wires on dist side to keep them from grounding out. On the other side of the dist where your 12V goes in (batt conection) there are to wires piggybacked on top of each other disconect them from dis and plug only the pink 1 into dist at the batt conection. Where the wires on the back of dist run into firewall there should be a vacume line disconect and plug on engine compartment side. Thats how you do the bypass and the spark control module can be removed from under the dash if you want to but its not hurting anything to leave it there. BEFORE YOU DO ANYTHING MAKE SURE YOU DISCONECT THE BATTERY. When all this is done you mite have to advance your timing 8-15 degrees. I had to advance mine 12 degrees. let me no if you have any problems. kyle yeo

Oct 18, 2010 | 1986 GMC C1500

1 Answer

1990 K5 Blazer DIED(Electrical?)?


There may be no injector pulse if the computor does not see a RPM signal.
There will be no spark if the ignition module does not see a dist pulse from the dist pickup.......a RPM signal.
Because you do not have both ......I would suggest to check/change the dist pick up.
Follow the wires from the ignition module inside the dist to the pickup which is also inside the dist.
If it is just a bad dist pickup....keep all your old parts as good spares.
Also...is the dist turning? to provide a RPM signal?
You will have to remove the dist to change the pick-up.....mark your timing locations......"rotor position" and "dist body location"before removal.
A quick test before installing the "repaired dist" .....plug it in the the truck wiring and turn on the key....DO NOT CRANK THE ENGINE OR YOU WILL LOSE YOUR DIST ROTOR CORRECT POSITION......as you spin the dist by hand .....the injectors should spray.

Aug 23, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

It turns over, but will not spark to start


99grand cherokee ign. system has no dist. its coils,unless its a99 with 98 ign......! you should have afault code,scan it,if its dist. type and what youre saying is right,check the auto shut down relay fuse and circuit,it will cut power to coil,could have broken electrical wire going to coil

Feb 28, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...