Question about 1991 Chevrolet Corvette

3 Answers

Reset change engine oil light - 1991 Chevrolet Corvette

Posted by on

Ad

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 346 Answers

Information taken from: http://www.idavette.net/tech/oilreset.htm

[quote]
The "Change Oil" indicator is reset by using a sequence of Driver Information Center (DIC) key presses as follows:

1. Turn ignition "ON", but do not start engine. (ALDL pin "G" should NOT be grounded.)
2. Press the "ENG/MET" button and release, then, within 5 seconds, press it again.
3. Within 5 seconds of Step 2, press and hold the "GAUGES" button. While the button is held, the "Change Oil" indicator will flash.
4. Continue holding the "GAUGES" button until the "Change Oil" indicator stops flashing and goes out, indicating successful completion of the reset cycle. This should take about 10 seconds.
If it does not successfully reset, turn ignition "OFF" and repeat the procedure from Step 1.
[/quote]

Posted on Dec 26, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Turn key on, press ENG/ MET button once, then again within 5 seconds. then press and hold the RESET button until the Change Oil light stops flashing and goes out, it may take 10 seconds.

Posted on Nov 16, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 580 Answers

Turn engine key on. Push gas peddle to floor three times. Turn key off then on. Light should be reset. Hope this helps you. If so please recommend advice.

Posted on Nov 16, 2009

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: oil was changed and check engine light was not reset

This is really easy! Please follow these directions:

Turn the key ON

Look at the odometer, and verify that it displays "ODO" and the total mileage traveled. If it is on "Trip A" or "Trip B", press the black stick next to the odometer to read "ODO", and the total miles traveled.

Turn the key OFF.

Press in, and HOLD the black trip meter reset button, hold it in.
DO not release it.

Turn the key ON; do NOT start the engine

Observe the Odometer display. The total mileage traveled will disappear, and you will see 5 dashes, then 4, then 3, then 2, then 1 dash, and finally, 5 zeros. Then, the total mileage traveled will redisplay.

Release the black trip meter reset stick.

This completes the reset procedure, and the light will be back on in 5,000 miles, to remind you of you next oil change.

Hope this helps, and thanks for choosing FixYa. Happy Thnkasgiving!

Posted on Nov 25, 2008

fyrebyrd1
  • 121 Answers

SOURCE: Code for reseting the Change Engine Oil Light

depress pedal fully 3 times within five seconds, sorry

Posted on Dec 05, 2008

  • 79 Answers

SOURCE: how to reset an oil change light

Turn the key on (do not start). Wail till the message comes up saying change engine oil. When message comes up hit the gas three times.

Posted on Apr 25, 2009

  • 1 Answer

SOURCE: reset engine oil change monitor

at 7000 you should definetly change oil, but depending on the make and model of your vehicle, to shut off of the check engine light will vary from a simple procedure in your owners manual, to having a obd 2 code detecter hooked up to identifie and delete codes

Posted on Jun 16, 2009

  • 6 Answers

SOURCE: HOW DO I RESET THE CHANGE OIL LIGHT ONCE THE OIL

look in the manual......turn the ignition to the on position not starting it of course and then pump the gas petal 5 times then the light will blink a few times turn off then back on...problem solved

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I had the oil changed but the change oil light is still on, how do i reset the computer? 2000 oldsmobile alero


How to Reset the Change Oil Light

After changing the engine oil, the system must be reset.

With the ignition key to ON, push the RESET button

located in the driver's side instrument panel fuse block. The

CHANGE OIL light will start to flash, press and hold the

RESET button again. The reset is complete when you hear
the chimes sound and the CHANGE OIL light goes out.

Oct 25, 2010 | 2000 Oldsmobile Alero

2 Answers

How to do I reset the maintenance service light on my 2007 Chevy Trail Blazer


there is no light for emissions testing on this vehicle. there is a ses light that can come on, indicationg a problem with the engine or transmission electronic system. this will require a scan tool to pull trouble codes. there is another light called oil life monitoring that needs to be reset after oil changes, which I suspect is what you are seeing. here is a picture of the light and the instructions for resetting.,

The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL SOON message being turned on, reset the system.
After changing the engine oil, the system must be reset as follows:
  1. Turn the ignition to RUN, with the engine OFF.
  2. Press the information and reset buttons on the Driver Information Center (DIC) at the same time to enter the personalization menu.
  3. Press the information button to scroll through the available personalization menu modes until the DIC display shows OIL LIFE RESET.
  4. Press and hold the reset button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
  5. Turn the key to LOCK.
If the CHANGE ENGINE OIL message comes back on when you start the vehicle, the Engine Oil Life System has not reset. Repeat the reset procedure.



485d3b2.gif

Sep 09, 2010 | 2007 Chevrolet TrailBlazer SS

2 Answers

Reset change oil light


hello, here is the instructions on how to reset the light

When the system has calculated that oil life has been diminished, it will indicate that an oil change is necessary. A CHANGE ENGINE OIL SOON message will come on. Change the engine oil as soon as possible within the next 600 miles (1000 km). It is possible that, if driving under the best conditions, the oil life may not indicate that an oil change is necessary for over a year. However, the engine oil and filter must be changed at least once a year and at this time the system must be reset.
If the system is ever reset accidentally, change the engine oil at 3000 miles (5000 km) since last oil change.
To reset the Engine Oil Life System, do the following:
  1. Turn the ignition to ON, with the engine off.
  2. Slowly fully press and release the accelerator pedal 3 times within 5 seconds.
  3. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and no chime is heard, repeat the reset procedure.
  4. Turn the key to OFF.
If the CHANGE OIL lamp comes back on when the vehicle is started, the engine oil life system has not reset. Repeat the procedure.

Jun 20, 2010 | 2001 Pontiac Grand Am SE

2 Answers

How to reset the change oil light for a 2007 lincoln town car. Hitting reset button doesn't do it.


FIRST press and release the setup button to display oil life= xxx
then press and hold the reset button for about 2 sec it should then display oil life set to 100%
--------------------------------
Just pressing the reset button when the change oil light comes on while driving will not reset the computer

Feb 15, 2010 | 2007 Lincoln Town Car Signature Limited...

2 Answers

Oil maintenece light is on. Oil level is good. Could a clogged filter make this light go on?


This should only be indicating time for an oil change. Now, if the red, check engine light comes on, then you have an oil/engine problem.

Possibly the maintenance light wasn't reset when the last change was done. If you don't have the owners manual to check, I found a referenced method (below) to reset it through AMSOIL synthetic oil products. Good Luck

To reset Engine Oil light. Turn the ignition key to RUN with the engine off. Fully press and release the accelerator pedal three times within five seconds. If the Change Engine Oil light is flashing, the system is reset. The light will flash for up to 30 seconds or until the ignition is turned off. If the light comes on again and stays on for 30 seconds at the next ignition cycle, it did not reset. You will need to reset the system again.

Feb 09, 2010 | Saturn L-Series Cars & Trucks

2 Answers

How do i reset my oil light? my husband changed


TURN THE IGNITION KEY TO RUN WITH THE ENGINE OFF.FULLY PRESS AND RELEASE THE ACCELERATOR PEDAL THREE TIMES WITH IN FIVE SECONDS.YOU HAVE TO DO THIS MORE THAN ONE TIME.ITS NOT GOING TO RESET FIRST TRY BUT DO THIS PROCEDURE.UNTIL THE CHANGE ENGINE OIL LIGHT WILL FLASH WHILE THE SYSTEM IS RESETTING.TURN THE KEY TO OFF.WAIT A FEW SECONDS.START CAR UP TO SEE IF CHANGE OIL LIGHT COME BACK ON.IF YES YOU HAVE TO TRY THE RESET PROCEDURE AGAIN.

Sep 26, 2009 | 2006 Chevrolet Equinox

3 Answers

Change oil light came on


In your owners manual there is a procedure listed for resetting thr oil change reminder/maintenance light. Some vehicles you turn key on..do not start it.. step on gas pedal all the way to the floor 3 times... then key off. others haver u hold the trip odometer reset button when u turn key on.
It varies from manufacture to manufacturer.

Jul 10, 2009 | 2006 Isuzu Ascender

2 Answers

How it reset service engine light


Is it the "oil change req." light? Your owners manual will have the process for reseting the oil change light.
If it is "service engine soon" light, the vehicle will need to be scanned with a professional scanner.

Jun 20, 2009 | 1996 Dodge Caravan

4 Answers

Reset oil life display after oil change?


THIS SHOULD BE IT.
How do I reset the Engine Oil life monitor and how does it work? TO reset To reset the Engine Oil Life monitor do the following:
Reset Oil life in NAV/DIC by (with car running) going to INFO>Oil Life>RESET
Press and HOLD until XXX turns to 100%
How does it work? The oil life monitor is a pretty sophisticated algorithm.

GM "The GM Oil Life System will automatically adjust the oil change interval based on engine characteristics, driving habits and the climate in which the vehicle is operated."

Feb 09, 2009 | 2007 Cadillac CTS 3.6L

1 Answer

Change oil light reset?


Hi Shady, here is the procedure for resetting the light.
Resetting Procedure
Follow this procedure to reset the GM Oil Life System™
  1. Turn the ignition to RUN, with the engine off.
  2. Fully press and release the accelerator pedal three times within five seconds.
  3. If the CHANGE OIL SOON light flashes, the system is resetting.
  4. Turn the key to OFF after the light has finished flashing, then start the vehicle.
  5. If the CHANGE OIL SOON light comes back on, the engine oil life system did not reset. Repeat the procedure.
With Trip Computer
  1. Press the MODE button until the light appears next to OIL LIFE.
  2. Press and hold the RESET button for three seconds. The oil life percentage should change to 100 percent.

Nov 02, 2008 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
1991 Chevrolet Corvette Logo

336 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...