Question about Hyundai Motor 1999 Elantra

Open Question

How do I get to the starter motor on an 98 elantra and what does it look like

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 52 Answers

SOURCE: 04 hyundau elantra clicks starter but no turning

It could be bad solenoid or starter. Take it off and have Auto parts store to check it for you.

Posted on Jun 18, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 hyundai elantra starter removal where are bolts located on the starter


It's bolted to the outer edge of your transmission. If it's a front wheel drive, it may be near the front of the motor, where the engine and motor connect. Should only have two bolts holding it on. Hope this helps!

Oct 02, 2017 | Hyundai Cars & Trucks

1 Answer

Where is my starter and how do I change my starter?


2000 Hyundai Elantra 2.0L MFI DOHC 4cylRemoval & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
  3. 2e15922.jpg

    Fig. Exploded view of the starter-XG 300 and XG 350

To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Air intake assembly Speedometer cable Shift cable Starter wiring connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 20-25 ft. lbs. (26-33 Nm) Starter wiring connectors and torque the battery cable nut to 88-140 inch lbs. (10-16 Nm) Shift cable Speedometer cable Air intake assembly Negative battery cable
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Speedometer and shift control cables Starter electrical connectors Starter motor
To install:
  1. Install or connect the following:
    Starter motor and torque the bolts to 25 ft. lbs. (34 Nm) Starter electrical connectors Speedometer and shift control cables Negative battery cable.

All Others
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable and wait at least 3 minutes Speedometer cable and shift cable from the transaxle Starter motor wiring Starter motor bolts and the starter
To install:
  1. Installation is the reverse of removal. Tighten motor retainers to 20-25 ft. lbs. (27-34 Nm).

Hope helps (remember rated this).

Jul 14, 2010 | 2000 Hyundai Elantra

1 Answer

04 hyundau elantra clicks starter but no turning


It could be bad solenoid or starter. Take it off and have Auto parts store to check it for you.

Jun 17, 2010 | 2004 Hyundai Elantra

1 Answer

Hyundai Elantra GLS 2003 starter does not work


it can if you have the proper tools and a little patience its not very hard at all it may be a little snug i cant remember off hand where the starter is located on that car but its relatively an easy fix.

May 21, 2010 | Hyundai Motor 2003 Elantra

1 Answer

03 Hyundai elantra wont start


it you can hear the starter motor spining but is not engaging into the fly wheel then the starter motor will need to be re-conditioned or replaced

Feb 26, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Cant find starter motor on 98 lantra wagon


give autozone or advance auto a try

Feb 10, 2009 | 1998 Hyundai Elantra

1 Answer

98 elantra will not start and headlights dont work


Check that the battery connections are tight and secure. If yes, check the starter motor connectors and check current to the starter while the ignition key is turned. If there is no current, try wiring the starter directly to the battery. If it turns, then the problem is in the wiring or it could be the starter motor fuse. If the starter does not turn, remove the starter and take it to an auto parts store for testing.

Jan 20, 2009 | 1998 Hyundai Elantra

1 Answer

WIPER ARMS WILLN OT MOVE


pinion gear or gearbox damaged. Replace.

Dec 26, 2008 | Hyundai Motor 2003 Elantra

1 Answer

Replacing starter for 2000 elantra gls


Verbatim from Haynes manual:

1. Disconnect the cable from the negative terminal of the battery.
2. If your working on a 2000 or earlier model, remove the air intake duct and the air cleaner assembly.
3. If your working on a 2001 or later model, detach the shift cables(s) from the transaxle.
4. Disconnect the speedometer cable from the transaxle.
5. Unscrew the nut and disconnect the battery cable from the starter motor, then disconnect the wiring from the solenoid.
6. Remove the starter motor mounting bolts, supporting the starter motor as the bolts are removed, and remove the starter motor.
7. Installation is the reverse of removal. Tighter the starter mounting bolts to 20-25 foot pounds.

Oct 11, 2008 | 2000 Hyundai Elantra

1 Answer

1999 hyundai elantra starting problems


remove the starter motor and check for damage/wear on the teeth of the starter motor and the ring gear teeth on the flywheel.turn the engine by hand while checking the ring gear so as to check the condition all the way around.hope this helps

Aug 27, 2008 | Hyundai Motor 1999 Elantra

Not finding what you are looking for?
Hyundai Motor 1999 Elantra Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...