Question about 2008 Chevrolet Silverado 2500HD 2WD

1 Answer

I would like to remove my truck bed on my 2500 hd. How is it attached as there are no bolts through the bed like the older models.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

NO BOLTS? Theres got to be some somewhere.

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate on star control module 2003 2500 hd crew cab with center console


Older ones, most times in front of the console. You don't have to remove the console to remove them. panel to remove though under the dash, both sides to get to nuts/bolts. Some of the old GM's were put up in the top dash. These are a pain. The dash has to be released(not pulled out) to get access to. just a note , I found them because they shorted out. Not to fix them. they killed data lines that wouldn't let the vehicle work right.

Jan 02, 2017 | Cars & Trucks

1 Answer

How do i remove the truck bed from 2005 chevrolet avalanch


disconnect all electrical wiring that is attached to the bed then disconnect the fuel filler tube. there is 4 bolts that hold the bed to the frame that you will have to remove. some trucks the bolts are removed from inside the bed and others from under the bed though the frame. then get help to pickup the bed and turn it to gain access to the pump or remove the bed from the frame.

Sep 19, 2014 | 2005 Chevrolet Avalanche

1 Answer

Change battery in 2012 silverado 2500


take positive and negative cables off of battery. now take battery hold down bolt out from back side of battery nearest to the cab. now lift battery out.

Nov 25, 2013 | 2012 Chevrolet Silverado 2500HD Work Truck...

1 Answer

Rear axle removal 98 gmc 2500 four wheel drive


the 2500 had two different axle housing the hd version had bolts in the center of the wheel under the hub cap the light duty you need to remove the cover in the center of the housing in the middle of the rear end then remove the 5/16 bolt the holds the center pin in the diff case then push the axle in and remove the large c clip then the axle shaft will pull out

Jun 30, 2012 | Cars & Trucks

1 Answer

How do you remove the tail light assembly to change bulbs on a 2003 frontier sc.


There are two phillips-headed bolts on each inside corner of the truck bed, behind the tailgate latches, that may be used to attach the brackets for the optional bed extender. If you have a bed liner installed, you will need to pull the corner of the liner back to expose the bolts.The factory bed liner needs to be flexed around the upper cargo hook to gain access to the two hex head screws that hold the tail-light housing against the body.Remove the screws so the tail light housing gets loose and easily comes out. this will help.please keep updated for further assistance if more help required. thanks.

Apr 29, 2010 | 2005 Nissan Frontier

1 Answer

How do you change a fuel pump on a 2002 GMC sierra, 1500 HD?


Remove the bolts that hold the bed box to the frame, disconnect the rear light wiring harness and the fuel filler pipe. Set up a pair of saw horses or something behind the truck. Then have four guys to lift on all four corners and set the bed on the stand you have ready. The bed is heavy! And there is the fuel pump! Replace with the new and take care to put the wiring harness for the fuel pump back where it was. Replace the bed, bolts and connect the lights. You are ready to go! Takes about two hours if you don't break the welds that hold the nuts for the bed bolts loose. Good luck!

Apr 17, 2010 | 2002 GMC Sierra 1500

3 Answers

I need to replace the fuel pump how would i do that in a chev silverado 2500   02   do i have to drop the tank and pull it out from the top?


either drop the tank or remove the bed, I have worked on some chevy trucks that you HAD to remove the bed as the bolts that hold the tank were inaccessible.

Feb 14, 2010 | 2000 Chevrolet 2500

1 Answer

How to install a tension pulley on 2002 chevy hd 2500


Remove belt remove center bolt,remove pully install new pully install bolt and tighten.Re-install belt.

Jan 22, 2010 | 2002 Chevrolet Silverado

1 Answer

2000 Chevy Silverado 2500 6.0 litre fuel pump


lifting the truck bed off the frame works best if you dont have a lift..take the fuel neck loose from bed and remove bolts holding bed to frame from the drivers side..loosen the bolts on passenger side..raise the bed on drivers side while watching bumper to bed clearance on passenger side.. you should get enough clearance to remove fuel pump from tank

Dec 26, 2009 | 2000 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

280 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...