Question about 1999 Dodge Grand Caravan

1 Answer

Removed spark plug wires without documenting how to replace them

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,608 Answers

If you just want to pull them off then just grab the boot part and twist and turn while pulling upwards.There are several tools for this too that you can find at the part stores.But not always needed.A pair of good hands works good to.Good luck.

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I replace spark plugs and wires on chevrolet equinox 2011 2.4 liter front wheel drive


First, I think it highly unlikely that a 2011 Chevrolet Equinox would be due for spark plugs yet. They only have to be changed every 100,000 miles.

Second, you could spend the rest of your life trying to change the spark plug wires on that vehicle and never accomplish it. 2011 Chevrolet Equinox is not equipped with spark plug wires.

Then, if the spark plugs were somehow in need of replacement at this time, I highly recommend that you do not try this at home unless you have access to compressed air to clean the debris out of the spark plug tubes. Otherwise, severe engine damage can occur. (I have replaced many cylinder heads because of DIYers attempting to change their own spark plugs without the proper methods and equipment.)

With all that said, you must remove the ignition coils to get to the spark plugs.

Apr 08, 2012 | 2011 Chevrolet Equinox

1 Answer

Describe your how fix my pontiac 2000 montana Problem changing spark plugs



Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.


Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the left side spark plug wires from the spark plugs.
  3. Remove the left side plug wires from the retaining clips.
  4. Rotate the engine for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. Remove the right side spark plug wires from the spark plugs.
  6. Remove the plug wires from the retaining clip.
  7. Remove the spark wires from the ignition coils.
  8. Remove the plug wire assembly from the engine.
    NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.

To install:
  1. Install the right side plug wires to the ignition coils and then the spark plugs.
  2. Install the spark plug wires to the retaining clip.
  3. Rotate the engine back to the original position.
  4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
  5. Install the spark plug wires to the retaining clips.

3.9L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the intake manifold cover.
  3. Remove the left side spark plug wires as follows:
    1. Disconnect the left side spark plug wires from the spark plugs.
    2. Disconnect the left side spark plug wires from the ignition coil.
    3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
    4. Remove the left side spark plug wire assembly.

  4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
    1. Set the parking brake.
    2. Shift the transaxle into neutral.
    3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
    4. Install the Engine Tilt Strap J-41131.
    5. Pull on the engine in order to rotate the engine forward.
    6. Tighten the strap.

  5. After rotating the engine, remove the right side spark plug wires as follows:
    1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.

  6. Remove the right side spark plug wire clip from the ignition coil bracket.
  7. Remove the right side spark plug wire assembly.

To install:
  1. Install the spark plug wire assembly.
  2. Install the right side spark plug wire clip at the ignition coil bracket.
  3. Connect the plug wires to the ignition coil and spark plugs.
  4. If the engine was rotated for access, return the engine to the original position.
  5. The remainder of the installation is the reverse order of removal.

Feb 05, 2011 | 2000 Pontiac Montana

3 Answers

How to change spark plugs


Those are as easy as they come these days. Mark each spark plug wire with a piece of tape with the cylinder # written on it, so as not to mix up the wires. Remove each spark plug wire by firmly grasping the wire by the boot (do not pull on the wire) and twist it back and forth a few times while pulling slowly. It should pop off without a great deal of effort. If it is seized and it breaks, you will have to replace the wire, or at the very least replace the terminals (if you can get some). Use an air hose and blow around the base of each spark plug to dislodge any loose dirt that could fall into the cylinders (not absolutely necessary, but a good idea). Remove each spark plug with a spark plug socket and extension and ratchet (I forget which size socket, it's either 5/8 or 13/16). Check the gaps of each new spark plug (typically around 0.035 in). re-install each new spark plug by hand (do not cross-thread them) and once you have ensured that the plug is threaded in properly, tighten the plug until it seats, and then tighten an additional 1/16 of a turn. Repeat this for the remaining plugs. Re-install wires to the corresponding spark plugs. You're done!

Jan 10, 2011 | 1983 Ford Crown Victoria

1 Answer

I have a missfire on a 2008 sedona. How do I find the bad cylinder


With the engine off first loosen all the spark plug wires and just lightly place them on the spark plugs.Now you will need some plastic plyers or something to remove the wires without getting shocked.
Start the engine and one at a time remove and replace each wire and see if it makes a difference in how the engine runs. If it does not make a difference then thats the problem cylinder. When you find the bad one check and see, maybe the coil for that cylinder is not sending a spark. Or if it is sending a spark, maybe that spark plug is no good.
I hope this helps you.

Oct 13, 2009 | 2003 Kia Sedona

1 Answer

I need the diagram to put the spark plug cables


2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
    NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
  2. Remove the intake manifold cover, if required.
  3. Disconnect the left side spark plug wires from the spark plugs.
  4. Disconnect the left side spark plug wires from the ignition coil.
  5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
  6. Remove the spark plug wire assembly.
  7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
  8. Disconnect the right side spark plug wires from the spark plugs.
  9. Disconnect the right side spark plugs from the ignition coils.
  10. Remove the spark plug wire assembly.
  11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.
To install:
  1. Install the spark plug wire assembly.
  2. Connect the right side spark plugs to the ignition coils.
  3. Connect the right side spark plug wires to the spark plugs.
  4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
  5. Install the spark plug wire assembly.
  6. Connect the left side spark plug wires to the spark plugs.
  7. Connect the left side spark plug wires to the ignition coil.
  8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
  9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
  10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
74d742b.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
306b531.jpg


Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
9313fa7.jpg


Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system
2c9af72.jpg


Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system
d929c16.jpg


Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system
f357cd3.jpg

Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system
09e9db9.jpg

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 2003 Chevrolet Malibu

1 Answer

Spark plug replacement.


woah removing engine to replace spark plugs ahah... sooo u needa see if u can use a WOBBLE with a extention to be able to reach the plug wires from underneith

May 31, 2009 | 2006 Hyundai Tucson

3 Answers

Can't get metal spark plug covers back in to place


how to take spark plug wires off 2003 yukon xl

May 15, 2009 | 2004 GMC Yukon

2 Answers

Spark plug replacement


Just pull hard, it does seem pretty tough, but you won't damage anything as long as its a hard consistent pull. Don't TUG, but pull increasing the pressure until it comes out. It needs to be a snug fit in there to keep debris/moisture etc from getting to your spark plug!

Jun 27, 2008 | 2004 Dodge Neon

Not finding what you are looking for?
1999 Dodge Grand Caravan Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...