Question about 1997 Mitsubishi Diamante

Open Question

I have a troubleshooting # p0443 its a faulty purge control solenoid... witch is connected to the canister do you have a diagram or a pic, where can i find this part in this type of car

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

Ad
  • 37 Answers

SOURCE: HAVE A TROUBLESHOOTING MESSAGE PO446

DTC P0446 Evaporative Emission (EVAP) Vent System Performance

The vehicle control module (VCM) monitors the performance of the evaporative emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this diagnostic trouble code (DTC) if the vacuum decay rate is more than a predetermined value. The VCM monitors the amount of vacuum and the amount of pressure in the EVAP system by monitoring the fuel tank pressure sensor. For this DTC, the VCM turns ON both the EVAP purge valve and the EVAP vent valve when the Conditions for Running the DTC are met. This applies an engine vacuum to a closed EVAP system. The VCM turns OFF both the EVAP purge valve and the EVAP vent valve when the system reaches a correct amount of vacuum. The EVAP system should quickly RELEASE the vacuum in the EVAP system with the EVAP purge valve OFF and the EVAP vent valve OFF (open). This test indicates a blocked or restricted EVAP vent path if the EVAP system fails to release the vacuum quickly enough.

3208f98.gif


Posted on Dec 06, 2008

  • 1168 Answers

SOURCE: locate canister purge solenoid for 2000 Buick

The evaporative canister purge valve is found between the upper intake manifold and the rear valve cover.

Posted on Nov 01, 2009

  • 1 Answer

SOURCE: I need to replace the canister purge solenoid

failed canister purge solenoid,plus fuel tank pressure sensor. 1996 pontiac sunfire,2.2

Posted on May 25, 2010

HD Road King
  • 70 Answers

SOURCE: 2006 gmc sierra 1500 4.3 . check engine light on.

More than likely the evaporator vent valve.

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a truck that popped up a P0443 code up and I've been trying to see what it is so I can get it fixed thank yo


P0443 - Evaporative Emission Control System Purge Control Valve Circuit Malfunction

Possible causes: - Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection

When is the code detected? An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms: - Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description: The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

P0443 Information for specific makes: P0443 ACURA
P0443 CHRYSLER
P0443 DODGE
P0443 FORD
P0443 HONDA
P0443 INFINITI
P0443 ISUZU
P0443 JEEP
P0443 KIA
P0443 LAND-ROVER
P0443 LEXUS
P0443 MAZDA
P0443 MERCEDES-BENZ
P0443 MITSUBISHI
P0443 NISSAN
P0443 TOYOTA
P0443 Evaporative Emission Control System Purge Control Valve Circuit...

Jun 03, 2015 | Cars & Trucks

2 Answers

Engine dies while driving. p0443 code. happens after I get gas.


P0443 Evaporative Control System Purge Control Valve Circuit Malfunction.

It is to do with venting the fuel tank.

It may simply be a loose gas cap.

May 12, 2015 | 2004 Kia Sorento EX

1 Answer

What code is po443


ossible causes
- Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection
help.jpg What does this mean?
When is the code detected?
An improper voltage signal is sent to Engine Control Module (ECM) through the valve.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
P0443 Description
The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.

Jul 21, 2014 | 2000 Mercury Mountaineer

1 Answer

P0443


Possible causes - Faulty Evaporative Emission (EVAP) Purge Solenoid Control
- Evaporative Emission (EVAP) Purge Solenoid Control harness is open or shorted
- Evaporative Emission (EVAP) Purge Solenoid Control circuit poor electrical connection

Apr 01, 2013 | 1999 Jeep Cherokee 4WD

1 Answer

Failed smog test Code PO443 ck. engine light on


This is the generic definition for the code.
Your year and model may be different. Possible causes include a faulty purge control valve or the circuit back to the computer.

P0443 Description The Evaporative Emission System (EVAP) canister purge volume control solenoid valve uses a ON/OFF duty to control the flow rate of fuel vapor from the EVAP canister. The EVAP canister purge volume control solenoid valve is moved by ON/OFF pulses from the Engine Control Module (ECM). The longer the ON pulse, the greater the amount of fuel vapor that will flow through the valve.
Read more: http://engine-codes.com/p0443.html#ixzz27RdAClP2

Sep 24, 2012 | 2000 Pontiac Montana

1 Answer

How do I fix fault code po443?


P0443 INFINITI - EVAP Canister Purge Volume Control Solenoid Valve

Possible causes- EVAP control system pressure sensor
- Damage harness or connectors to the Purge Control Valve
- The valve circuit is open or shorted
- EVAP canister purge volume control solenoid valve may be faulty (The valve is stuck open)
Tech notes It's a very common problem with Infiniti vehicles. If the harness is not damaged, it's very likely that the problem is the canister purge volume control solenoid valve.


Read more: http://engine-codes.com/p0443_infiniti.html#ixzz1yqKLq8YE

Jun 25, 2012 | Infiniti J30 Cars & Trucks

1 Answer

I have a plymouth neon and need to find out how to fix code p0443


P0443 Code is purge control valve circuit. Go to the driver side near the battery or better yet use the underhood sticker emission diagram That black cylinder is the canister,on it is the purge valve which hoses lead to the intake. make sure the hose are not torn,or leaking or disconnected if it is clear the code rerun the monitor (just drive it its 2 trip),because more likely that would be the code for P0443.Just because its a valve circuit doesnt mean its the valve circuit the ECM sent a command to purge and the MAP did not detect a purge,The ECM doesnt know if it is caused by a bad purge solenoid a disconnected line for the purge (normally closed) so it coded it if you want to fix it it is either the hose of the purge or the valve itself.

Mar 08, 2012 | Plymouth Neon Cars & Trucks

2 Answers

Po443


Hi, the p0443 code is for Evaporator Canister Purge Control Solenoid Valve. The canister has charcoal in it to absorb vapors from the fuel so it can't be released into the air. When the system detects that the canister needs flushing , the purge control solenoid opens to purge the canister and the vapors are consumed by the engine,sorry I don't know where the location of this is on your car but purchasing an AUTOMOTIVE REPAIR MANUAL by Haynes from an auto parts store would be helpful. I believe the problem can be as simple as a gas cap not being tight enough! There are many things that have to work for the system to function like the solenoid / current to solenoid / leaks / stop ups etc. Like many things it's a process of elimination......... Good luck.

Jun 04, 2011 | 1997 Nissan Maxima

2 Answers

Code says evaporator purge solenoid


Which code specifically? Do not assume you need a new solenoid. Our recommendation will depend on the specific code and some troubleshooting results. I usually recommend checking over all the EVAP vacuum lines and the gas cap too whenever there is a purge valve code. Check the vacuum lines at the cannister in the left rear bumper. I will paste info on the purge solenoid below.

P0440 Evaporative emission (EVAP) system - malfunction

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0441 Evaporative emission (EVAP) system - incorrect flow detected

Possible causes: Hose connection(s), intake leak, EVAP canister purge valve


P0442 Evaporative emission (EVAP) system - small leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0443 Evaporative emission (EVAP) canister purge valve - circuit malfunction

Possible causes: Wiring, EVAP canister purge valve, ECM


P0444 Evaporative emission (EVAP) canister purge valve -open circuit

Possible causes: Wiring open circuit, EVAP canister purge valve, ECM


P0445 Evaporative emission (EVAP) canister purge valve -short circuit

Possible causes: Wiring short circuit, EVAP canister purge valve, ECM


P0450 Evaporative emission (EVAP) pressure sensor - circuit malfunction

Possible causes: Wiring, EVAP pressure sensor, ECM


P0455 Evaporative emission (EVAP) system - large leak detected

Possible causes: Hose connection(s), intake leak, EVAP canister, EVAP canister purge valve


P0456 Evaporative emission system - very small leak detected

Possible causes: Mechanical fault, hose connection(s), EVAP pressure "sensor


P0457 Evaporative emission system - leak detected (fuel cap loose/off)

Possible causes: Mechanical fault, hose connection(s), EVAP pressure sensor


P0458 Evaporative emission system, purge control valve -circuit low

Possible causes: Wiring short to earth, EVAP valve


P0459 Evaporative emission system, purge control valve -circuit high
Possible causes: Wiring short to positive, EVAP valve


Evaporative Emission Purge Solenoid

Description & Operation
The duty cycle EVAP canister purge solenoid (DCP) regulates the rate of vapor flow from the EVAP canister to the intake manifold. The Powertrain Control Module (PCM) operates the solenoid.
During the cold start warm-up period and the hot start time delay, the PCM does not energize the solenoid. When de-energized, no vapors are purged. The PCM de-energizes the solenoid during open loop operation.
The engine enters closed loop operation after it reaches a specified temperature and the time delay ends. During closed loop operation, the PCM cycles (energizes and de-energizes) the solenoid 5 or 10 times per second, depending upon operating conditions. The PCM varies the vapor flow rate by changing solenoid pulse width. Pulse width is the amount of time that the solenoid is energized. The PCM adjusts solenoid pulse width based on engine operating condition.
Removal & Installation
The duty cycle evaporative (EVAP) canister purge solenoid is located in the engine compartment near the brake master cylinder.

  1. Disconnect electrical connector at solenoid.
  2. Disconnect vacuum lines at solenoid.
  3. Lift solenoid slot from mounting bracket for Removal & Installation.

To Install:
  1. Position solenoid slot to mounting bracket.
  2. Connect vacuum lines to solenoid. Be sure vacuum lines are firmly connected and not leaking or damaged. If leaking, a Diagnostic Trouble Code (DTC) may be set with certain emission packages.
  3. Connect electrical connector to solenoid.
Purge solenoid location:

jturcotte_65.gif
EVAP cannister location:
jturcotte_66.gif

Nov 05, 2010 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1997 Mitsubishi Diamante Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...