Question about 2001 Ford Focus

1 Answer

Can`t get the drum and bearing of the spindle of 2007 focus

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,341 Answers

I assume you are talking about the rear wheel which has got a drum brakes here...you will need a hammer and give a few hit all around its circumference while you try to pull the drum out...this should help you to get this out..and hence to the bearing.Hope this helps.

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

2 Answers

2006 ford focus zx4 se brake drums wont come off.. how do you take them off correctly


you need to loosen the adjustment of the break first for the drum to came off...

Jun 09, 2009 | 2006 Ford Focus

1 Answer

How do you release the rear brakr shoes to remove the drum and bearings?


Remove or disconnect the following:
  • Rear wheel
  • Wheel speed sensor, if equipped
  • Brake drum, bearing and spindle assembly
  • Brake shoe hold-down springs and pins
  • Brake shoe assembly from the wheel cylinder and anchor block
  • Parking brake cable
  • Lower return spring
  • Upper return spring
  • Primary shoe from the strut and brake shoe adjuster
  • Parking brake return spring
  • Secondary shoe from the strut support
I hope this answers your question. Best of luck!
Greg

Jun 28, 2011 | 2003 Ford Focus

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.


The torque setting 49 ft. lbs.


Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

2 Answers

Exacly how to remove rear brake drums ? 2001 Ford Focus SE. I don't want to remove the hub & spindle. I simply want to replace the drums & Brake shoes.


The drum and hub are one assembly on that vehicle so you will need to remove the dust cap in the center of the drum and remove the large axle nut. The drum/hub/bearing assembly will then pull off of the spindle.

If you want to replace the drum you will either have to find one with a bearing already installed, Have your old bearing pressed out of the old drum and pressed into the new drum, or have new bearings pressed into the new drum.

When installing the new drum it is very important to tighten the axle nut to the proper spec. I can get that spec for you if you need it.

Apr 06, 2011 | 2000 Ford Focus

1 Answer

Wheel Bearings how do you change them


this requiers a shop press and removing the spindle from the car, remove the c clamp from the back side of the spindle and use the press to push the bearing out of the spindle, and then reverse the steps to put the new bearing in..

Aug 27, 2010 | 2003 Ford Focus

1 Answer

How to replace rear wheel bearings


If it has drum brakes, you'll need to take off the center dust cap, remove the cotter pin, remove the nut and washer holding the drum on. The outer bearing should fall out, the inner bearing usually stays in the drum, due to the grease seal. With the front bearing and washer off, put the drum back on and install the nut, then pull the drum, allowing to the nut to catch the inner bearing as you pull off the drum, and that should leave the inner bearing and seal on the spindle. Pack the new bearings with grease, install the inner one in the drum and tap in the grease seal in place, but the drum back on and install the outer bearing on the spindle, the wash, nut, cotter pin and dust cover. Tighten the nut snug and turn the drum a few times and snug up the nut. Don't overtighten it.

Apr 29, 2010 | 1991 Volkswagen Jetta

1 Answer

How do i remove the brake drum of a 1997 hyunidai excel do i need to remove the centre nut that also takes out the wheel bearing


With Rear Hub Bearing
  1. Raise the vehicle and support safely.
  2. Remove the wheels.
  3. Remove the dust cap, cotter pin and loosen the locknut
  4. Remove the washer and outer wheel bearing.
If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes.
  1. Remove the drum with the inner wheel bearing from the spindle.
To install:
  1. Install the drum on the spindle.
  2. Install the outer wheel bearing and washer.
  3. Tighten the locknut to 108-145 ft. lbs. (150-200 Nm). Turn the brake drum while tightening the spindle nut to seat the wheel bearings.
  4. Install the cotter pin and dust cap.
  5. Install the wheels
  6. Adjust the rear brakes.

Apr 23, 2010 | 1997 Hyundai Accent

1 Answer

I'm dont able to remove rear drum on ford focus 2005


the bearing needs to come apart remove the silver cap you should see a cotter pin holding the spindle nut remove the pin then the lock shield for jam nut then remove jam nut be careful as bearing may fall out there is a washer between jam nut and bearing then you should be able to remove drum

Aug 18, 2009 | 2007 Ford Focus (3 Door) Hatchback

1 Answer

How do I change the front wheel bearing on 2003 ford focus zx3


Remove the spindle, remove the hub from bearing, remove lock ring, press old bearing out, press new one in, if old hub is reusable, press into bearing, reinstall spindle.

Jun 27, 2009 | 2003 Ford Focus

Not finding what you are looking for?
2001 Ford Focus Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...