Question about 1988 Chevrolet S-10

1 Answer

I replaced the master cylinder and slave cylider on a 1988 chevy s-10 2.5l v4. I still have no pressure in the clutch. whats next.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 72 Answers

Have you fully bled the system? have you gone round all seals (including the clutch housing) and checked for leaks in there?

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch slave cylinder wont come up to presure


If the master cylider and slave cylinder have been rebuilt and they won't hold, it sounds like there is an internal leak in one end of the system.
Could be a damaged (cracked) cylinder where the rubber cup will not seal.

Aug 19, 2012 | Hyundai Tiburon Cars & Trucks

1 Answer

92 chevy z71 4wd pickup clutch slipping


Being a single piston master i do not see how it could be holding pressure on the the slave cylinder. if your clutch petal is releasing high you need a new clutch and pressure plate

May 29, 2017 | 1992 Chevrolet K1500

2 Answers

What could cause a clutch pedal in a 1996 honda accord to lost pressure


no fluid in the clutch reservoir due to a failed clutch slave cylinder
time to replace both the clutch slave and master cylinder

Dec 02, 2017 | 1996 Honda Accord

1 Answer

The clutch will not engage properly on my 1988 toyota pickup. Already replace clutch master cyclinder and clutch slave?


There are a couple of possibilities; worn clutch plate, failed pressure plate, possible hanging up of the throw-out bearing. Also, some hydraulic clutches have a throw adjustment on the slave cylinder that may need adjustment after replacing the slave cylinder.
If you plan on more DIY maintenance, I would highly recommend buying a Haynes service manual, you'll find the $25 well-spent:
Toyota pickup manual

Mar 31, 2011 | 1988 Toyota Pickup

1 Answer

I replaced clutch master cylider and sleigh cyclinder and still dont have any clutch pressure padel wont stand up and cant get any gears


?. Did you bench bleed all of the air out of the 2 master cylinders before installing on your vehicle, it sounds like that it has air in the sysytem, try bleeding the cltch master cylinder and the bleed off the slave cylinder, that should put you on par.

Oct 20, 2010 | 1990 Nissan 300ZX

2 Answers

My clutch pedal is stuck to the floor??


It is most likely a hydraulic clutch, and it is most likely leaking at the clutch slave cylinder. Check the clutch master cylinder for fluid, it should be a small master cylinder looking thing with a fill cap next to the brake master cylinder and booster unit. If it is empty fill it with the same dot 3 brake fluid that you use for your brake master cylinder, and make sure that you are pouring the fluid into the clutch master cylinder reservoir and not the rubber seal that should be under the fill cap. After filling the clutch master cylinder up with fluid, then try and pump up the clutch pedal. It might take a while to pump up hydraulic pressure, and you might also have to work the pedal a few times by hand at first.

Also, you might have to bleed the clutch at the slave cylinder if it will not build up enough pressure to release the clutch.

Apr 28, 2010 | 1988 Mazda RX-7

5 Answers

Stuck clutch pedal on a Mazda B series truck


Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Clutch pedal goes to floor


Its sounds like a bad clutch cylinder or bad slave cylinder or fluid leaking. First check brake fluid level in clutch master , and check for a leak in clutch system. If there are NO leaks, then you either have a bad clutch cylinder or a slave cylinder. Bleed clutch at bleeder screw on slave cylinder and make sure there is pressure from master cylinder. If there is pressure then slave cylinder may be bad replace slave and bleed and that should take care of you problem. If master is bad then replace bleed system ad you should be good. Contact if you need more help. Thanks for using FIX YA.

May 16, 2009 | 1988 Honda Accord 4 Door

1 Answer

1988 Prelude clutch problem


either the master cylinder for the clutch needs fluid or it is by-passing or the slave cylinder for the clutch is worn out. Good luck and remember to rate all of the solutions that you get, thanx.

Oct 30, 2008 | 1991 Honda Prelude

Not finding what you are looking for?
Cars & Trucks Logo

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...