Question about 2003 Honda Odyssey

2 Answers

Can an individual replace rear tail light housing on the liftgate

Can an individual replace the rear tail light housing on the liftgate on a 2003 honday odyssey? It is the passenger side.

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 7,353 Answers

Sure you can, just remove the back panel and there will be small nuts holding the rlight in.

Posted on Nov 16, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Hi yes its not a problem make sure you clean the area where the mounting screws go in as that also acts as an earth good luck

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change brake light bulb on a 2014 fiat 500L


https://www.fiatusa.com/download/pdf/manuals/2014-FIAT-500L-OM-1st.pdf

it's in your owners manual page 358 chapter 7

you need a torx 20 screwdriver or bit

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
3. Remove the four screws (using a T20 driver) and separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.

Center High-Mounted Stop Lamp (CHMSL)
This light is an LED assembly. See your authorized stealership

Mar 30, 2015 | Fiat Cars & Trucks

1 Answer

Need to replace stop light


Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif

Oct 18, 2010 | 2004 GMC Envoy

1 Answer

Do I remove the entire cover or the little door thats atached to this cover on the passenger side? There are 3 brake lights that were recommended to replace. Driver side and passenger side plus the third...


Lamp, Rear Hi-Mount Lamp Assembly
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Raise the liftgate.
  1. Remove the liftgate door trim panel (46404) . Refer to Section 01-05 for the removal procedure.
Trim Panel, Liftgate Door Removal
  1. Disconnect thebattery ground cable (14301) .
  1. On vehicles with a rear window wiper, remove the three rear wiper motor cover screws and remove the rear wiper motor cover.
  1. Pry the liftgate door trim panel (46404) away from the liftgate.
  1. Disconnect the luggage compartment lamp electrical connector.

    n11098a.gif

  1. Remove the liftgate door trim panel
  1. Rotate the rear hi-mount lamp socket counterclockwise and remove it from the rear hi-mount lamp (13A613) .

    k20521a.gif

  1. Remove the two rear hi-mount lamp housing nuts and remove the rear hi-mount lamp lens and housing.

    k20523a.gif

Oct 18, 2010 | 1995 Ford Aspire

1 Answer

How do i replace brake light


Rear: Brake, Back-up, Tail, Turn signal (3 bulbs, all # 3157):
To access the rear bulbs, open the liftgate and remove the two phillips head screws from the side of the housing as shown in the center photo above. Slowly and firmly rotate the assembly away from the vehicle until it disengages from the ball pin socket that secures it in back.

Each of the three light sockets, all containing the same exact bulb type, can be removed by turning them counter-clockwise 1/4 turn.

(Note: Replacement sockets are available separately, Jeep P/N 4676589)

ff7252a.jpg

(click for zoom)

Hope this helps (remember rated and comment this).

Sep 07, 2010 | 2002 Jeep Grand Cherokee

1 Answer

Drivers side rear blinker light needs replaced


Open the tail gate, and you will see on the side of the tail light housing two screws that you will need to unscrew in order to take the housing out. If it is the tail light ,that is on the actual gate, open the tail gate and remove the plastic bed liner there are few of screws that need to be removed. Hope this helps you fix it.

Apr 17, 2010 | 2003 Subaru Baja

1 Answer

Rear turn signal how to change bulb


open the liftgate remove the screws holding the tail,stop,turn signal and back-up light assembly to the rear door opening. seperate the light assembly from the vehicle body. disengaging the hook holding the outer end of the light assembly to the body. swing the housing out to access the bulb holders. rotate bulb holder and remove blown out bulb. installation is the reverse of removal. hope this will help!!!

Apr 03, 2010 | 2005 Dodge Grand Caravan

1 Answer

I would like to know how to remove my 03 lincoln aviator tail lamp as I need to replace it. Thank you..


here's mountaineer, it should be similar

SECTION 417-01: Exterior Lighting 2002 Explorer/Mountaineer Workshop Manual
REMOVAL AND INSTALLATION Rear Lamp Assembly —Mountaineer Removal and Installation
  1. Raise the liftgate and remove the rear lamp assembly screws.
  1. Remove the rear lamp assembly.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.
    • If necessary, install new tail lamp bulbs.
8966cfe.gif

Aug 01, 2009 | 2003 Lincoln Aviator

2 Answers

Need help for rear tail light assembly on my 2003 trailblazer


Most of the time you can simply remove the tail light assembly from the car pretty easy and just a few screws. If it sdoes not have the screws going through the front of the housing then its rear mount and must be done by lifting the tailgate to get access. Once in the vehicle you should beable to remove the plastic housing covering up the assembly from the inside. Remove the 3-4 screws or bolts and the tail light assembly. Install the new one just the reverse. Pretty easy just take your time.

Joe

May 28, 2009 | 2003 Chevrolet TrailBlazer

1 Answer

2003 Honda Odyssey Brake light replacement


open the rear hatch. Between the tail light housing and the rear hatch opening there is a trim strip with two flush fitted flap doors. Insert a small straight blade screwdriver into the small slot on the tail light side of the flap. Pry gently inboard and the small flap will open (the hinge side of the flap is on the side of the rear hatch opening.) Now you can remove the screws that hold the tail lamp assembly in place. Finally, there is still a "spear point" clip that fits into a socket near the front outboard corner of the assembly. Gently pry with a tape wrapped screwdriver (avoids scratches) and force the assembly straight back. The clip should release and free the assembly so you can change the bulb(s).

Jan 22, 2009 | 2003 Honda Odyssey

1 Answer

2003 Saturn Vue rear liftgate won't open


The easy part is you just need the latch for the liftgate. The hard part is getting to it and opening the liftgate to replace the latch. You should be able to pull the liftgate trim off most of the way with the gate closed and try to manually actuate the latch to open the gate. You may have to go so far as breaking the latch from the inside to open the gate and then replace your latch.

Nov 10, 2008 | 2003 Saturn VUE

Not finding what you are looking for?
2003 Honda Odyssey Logo

411 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...