Question about 1991 Honda Prelude

1 Answer

Remove gear box

How to remove gear box from 1991 prelude manual

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Honda Master
  • 1,779 Answers

This is a big job, and I list what to do, but I wou9ld also recommend you purchase a good manual, or go to alldatadiy site to purchase on line access to diagrams, info etc (great site) 1. disconnect battery ground cable @ battery and trans. case, unlock steering column, put trans. in neutral 2.disconnect back u light switch wires + black and white wire from starter solenoid 3remove air cleaner assembly 4.remove power steering speed sensor from the transaxle w/out removing the power steering hose 5remove the shift cable and the select cable from the top cover of the transaxle.Remove the mounting bolt from the cable stay. Be sure not to bend or kink the cable more than necessary. Remove both cables and the stay together. 6 Remove upper transaxle mounting bracket, remove the 4 transaxle to block attachment bolts that must be removed from the engine compartment. 7 Raise and support the vehicle safely. Remove both front wheels and splash shield 8 Drain the trans oil, remove clutch save cylinder. The cyl may be moved out of the way w/out disconnecting the hose 9 remove the center beam, remove the right radius rod completely, remove the right and left shafts. 10 remove the engine stiffener, remove the clutch cover, support the transaxle w/ a trans jack 11 remover the 3 lower bolts from the rear engine mounting bracket. Loosen but do not remove the top bolt. This bolt will support the weight o f the engine. 12 remove the 2 remaining engine to transaxle bolts. 13 with transaxle on a transmission jack disengage the input shaft from the clutch disc and lower the transaxle out of the vehicle. DO NOT ALLOW THE TRANSAXLE to hang on the input shaft. Once removal begins, remove it completely from the engine. Good luck, and please rate this, it took a while to get it down!

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1991 honda prelude the speedo fluctuates up and down when driving the part no# -on this cluster is HR-0161 PMMA is there a quick fix


Your speedo is not electric so it is driven by a cable. There is a problem in two locations. First is the cable itself not having the proper amount of grease and it is starting to fray. Second is the gear inside you speedo and it is worn out or some of the gear teeth is missing. Unfortunately there is not a quick fix. Good Luck

Jan 07, 2011 | 1991 Honda Prelude

1 Answer

How hard or expensive is it to change a speed sensor in a 1991 Honda Prelude SI?


The speedometer sensor is located on the top of the transmission. It is held on by one bolt. Remove the bolt and gently pull and turn the speedometer sensor and the whole assembly will come out of your transmission.


Park your Honda Prelude on a level surface, activate the emergency brake and place blocks behind the back tires for safety. Disconnect the negative battery cable with a terminal puller.

Raise the vehicle on the side of the wheel speed sensor's location. Remove the wheel and tire assemblies.

Disconnect the sensor electrical connection from the wiring harness.

Take note of the connection location for the sensor retainers, grommets and clips. You will need to know this information for the installation process.

Start at the connector end of the sensor cable and remove grommets, clips and retainers in order to free the harness.

Unscrew the sensor mounting bolt and remove the sensor from the differential housing.

Install the new speed sensor by reversing the removal process. Loosely secure the sensor and sensor harness connection in place, taking precaution to keep the harness from twisting or bending. Once in place, torque the sensor mounting bolt to 16 foot pounds (22 Nm). Tighten any bracket bolts to 84 inch pounds (10 Nm).

Lower the vehicle safely and reconnect the negative battery cable. Refer to your owner's manual to perform an ABS system check to confirm that you installed the sensor properly.

Oct 01, 2010 | 1991 Honda Prelude

1 Answer

My 1991 Honda prelude has lost a headlight ground. Where is it?


There are fuses for the headlights, right and left. G201 is the ground connection number. I have no picture but its located RH Center of eng compartment. Usually on the radiator support.

Dec 16, 2009 | 1991 Honda Prelude

2 Answers

1991 honda prelude speedometer not working,what is


Probably the Vehicle Speed Sensor (VSS). Cheap and easy to change (see ebay), once found! Probably on top of gearbox, to rear.

Aug 06, 2009 | 1991 Honda Prelude

1 Answer

Where is the thermostat located on a 1991 honda prelude


its located on the upper radiator hose. You could see a joint in which the hose is attach. remove the 2 bolts and make sure after replacing it to seal it properly before bolting it back.

Jul 10, 2009 | 1991 Honda Prelude

1 Answer

I have a prelude 91,aut.trans,all speed work but only in reverse dosn´t work.


reasons for no reverse 4th gears or worn and damage-reverse gears worn-4th clutch is faulty-control cable misadjusted-servo shaft stuck-1-2 shift valve faulty-electrical system is faulty.

Jun 13, 2009 | 1991 Honda Prelude

1 Answer

How do I change the alternator on a 1991 honda prelude...is it easy to do myself or should I take to a mechanic if its location is difficult to reach?


it shouldn't be to difficult to do if it is accessible. Disconnect the battery first, then loosen and remove belt, remove wires and plug from alternator, then remove connecting bolts to the alternator, just go back in reverse order. Hope this helps!

Dec 15, 2008 | 1991 Honda Prelude

1 Answer

1991 prelude drivetrain problem


Wow, that's weird! If the speedometer is moving, but you aren't, then yes, something in the axle is not connected to the wheel. Were there any weird noises or symptoms before this happened? Either the cv joint is completely shot (u should have heard noise when turning a long time before this) or the spline could be stripped, but that is something I haven't heard of. If the clutch was shot, the engine would rev, but speedo is connected to transmission, so the speedo would not work if the clutch didn't. Let me know if anything was going on before this happened, I have a 91 Prelude (2nd since 1994, love it). countrycurt0

Sep 16, 2008 | 1991 Honda Prelude

Not finding what you are looking for?
1991 Honda Prelude Logo

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...