Question about 2004 GMC Sierra Denali

1 Answer

I need to get under the cup holder section of the console

I need to get under the cup holder section to remove a credit card. Can this be done without removing the complete console?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 139 Answers

Hello,
I hate to be the berrer of bad news but unless you can sneek a grab at it from the side you will need to remove the whole console. I would try some of those 4 jaw flexible pincher grabbers most parts stores would cary them.

Roy

Posted on Nov 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

I AM TRYING TO TAKEOUT A CENTER CONSOLE OUT OF A 2000 CHRYSLER INTREPID


Hi Ken, I'm glad to help! Ken I have removed so many of the center consoles on Intrepids, heck I can do it in my sleep. I'm not sure how far you have gotten removing it. But there are some hidden screws under the rear cup holder. Pull the rear seat cup holder out and there is one in the very front and 2 down inside the slot. Those are the only ones you need to remove the other screws simply hold the cup holder in. The rest of the removal is very easy. Hope this helps and have an awesome day Ken!

Apr 18, 2014 | 2000 Chrysler Concorde

1 Answer

Replacing cup holder


I assume you mean the one that flips up in the center console?

If so, there are three likely issues.

1) did you slide out the retainer from the upper screw? the top screw had a cover that had to be pried off. you then took the screw out. Lastly you have to slide out the plastic retainer that the screw went into. It slides out towards the opening.

2) you have to have the cup holder partially open to remove it. the hinged part that folds up is stored in the cavity under the console when closed. you have to open the cup holder and keep pushing until the front of the cup holder lip comes up. Work the cup holder up and down until it comes out.

3) the cup holder is stuck in place due to years of spilled liquid. If you've done the above, then you can either spray soapy water on the creases around the opening and let it set, or you can apply strategic brute force.
Be aware through. if this is the center console cup holder just behind the gear shifter. There are two screws and nothing else to hold it in. Just be carefull....

Mar 17, 2014 | Volvo S80 Cars & Trucks

1 Answer

I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack


Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

May 02, 2012 | 2006 Chrysler Pacifica

1 Answer

Want to remove console to replace cup holder on 05 crossfire.how do you remove hand brake handle?


right above the cup holder is a cover the length of the cup holder remove it pops out.
2 screws hold the cup holder 2 hold the bezel u only need to take the 2 for the bezel out. The rest will pop off and disconnect the connectors for the AC and so on.

Mar 03, 2011 | 2007 Chrysler Crossfire Convertible

1 Answer

I have an '08 TL with a very annoying object sliding back and forth when I brake and accelerate. Sounds like it is under the cup holder. I removed the trim on both sides. That is where I am stumped. Is...


the center console will prob. have to be removed , there are hiden screws, be patiant and thuroly look before just ripping out cup holder.

Feb 11, 2011 | 2008 Acura Tl

1 Answer

How do I remove the center front console, where coffee cup holder hood is?


Loosen the hex head set screw from the front of the Shifter knob. Pull it off, then remove the screws on the lower sides, as well as the ones hiding under the rubber cup holder. The entire assemble will now lift off.

Oct 29, 2010 | 2004 Chrysler Pacifica

1 Answer

HOw do you fix the slave cylinder on a 2004 gto?


On 2004-2006 GTOs, you must have a lift. Set the parking brake. Disconnect negative battery terminal. Remove one screw from the cup holder bezel. This screw is under the business card holder, in the radius of the change holder. The shift knob is held in place by a set screw, I believe it is a hex. Next, pull the cup holder bezel up from the rear, by the console lid. Disconnect the window switches and traction control switch. Now remove the bezel and put it in the passenger seat. Raise the vehicle and set the lift arms done on the locks. The exhaust system from the catalytic converters to the tips needs to be taken out. Next step is to remove
the three bolts from the drive shaft damper. Next, remove the three bolts attaching the damper to the pinion yoke. These bolts are E torx bolts, I believe E14. After that, remove the drive shaft support bearing. These are 13mm bolt heads. Next remove the drive shaft, the transmission yoke is a slip yoke. From there, disconnect the speed sensor connector, back up lamp switch connector, and the skip shift connector. Next, disconnect the master cylinder fluid line which is on the driver's side of the transmission. Get a telescoping jack under the transmission and take out four crossmember bolts. Believe the bolt heads are 15mm. Next, take out the six bolts that secure the transmission to the bellhousing. These bolts should also be 15mm, but could be 14mm. From there, pull back on the transmission and lower the jack. The slave cylinder is attached to the front of the transmission, these bolts are 10mm heads. Installation is reverse of removal! Have fun!

Jan 23, 2010 | 2004 Pontiac GTO

2 Answers

Mouse in my heater , do I need to take apart center counsel, how is this done! And what else needs to come apart.


try setting a mouse trap up as it will become hungry and catch it but if a nest has been built you will indeed need to remove it .to prevent further issues .sometimes they are sheet metal screws others are riveted in but it should be a fairly easy job also the aid of a mirror and a flashlight will allow you to view that which you cannot see in some areas

Sep 08, 2009 | 2000 Pontiac Grand Prix

3 Answers

2003 Sahara Landcruiser Console removal


Dear Sir/Madam,

Just got done doing it actually. remove all the visible screws.. two in the front two above the cup holders. 4 Screws total there. Next pull off the black part that has the cup holders. Under that there are 2 screws holding the console to the floor. Remove them. Then go to the sides on the back.. There are two covers they are oval shaped. pop them off and remove the 4 bolts in there. Then pull off the top part. Next pull out the whole console. The only part thats left it the metal support. It will have 4 bolts and 4 screws attaching it to the floor. Then your done. Except for the two ugly holes where there is no carpet.

Go to this link and follow the 7 steps to fix your problem.....

http://www.ehow.com/how_2092450_replace-car-console.html

Thanks
good luck



Aug 07, 2008 | 2003 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

366 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...