Question about 2006 Pontiac G6

1 Answer

How do you adjust the highbeam headlight on 08 G6

How do you adjust the high beam headlights on a 2008 pontiac G6? I found the adjustment hexhead screw for the lowbeam, but cannot locate a screw either on top or behind the front engine shroud. I appreciate your help.

C

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 175 Answers

There is no separate for the highbeam. Basically, you are forced to use one screw for both and have to compromise

Posted on Feb 06, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Driver side headlight goes dim on high beam while passenger side is bright


bad connection or bad earth check all connection or bulb

Jan 24, 2016 | Cars & Trucks

1 Answer

Hi I got a problem with my Volvo V70 headlights. When i turn on highbeam, the lowbeam reflector adjust itself up, providing more light to the high beam. After i mounted a h9 55w xenon kit into the hi


it may need reset at the dealer to accomodate the new style/type of lamp..unless the cars', original factory setting does not allow for that change to be made.. they can tell you either way..

Dec 24, 2013 | Volvo Cars & Trucks

1 Answer

No headlights only on highbeam


Dimmer switch most likely out of adjustment or faulty, but could be your headlight switch.

Dec 08, 2013 | 1997 Chevrolet Cavalier

1 Answer

2002 pontiac grand prix gt. High beams are dimmer


A loose ground wire to the headlight will keep it dim,Or a headlight adjustment will bring the headlight up.If you can have your headlight turned on a garage door or something at night,and then watch as you change your headlights from low beam to high beam which ones are higher.the last thing to verify is that your high beam headlights are not the plastic lens type that turn dull which cuts the light power.

Dec 31, 2009 | 2001 Pontiac Grand Prix

2 Answers

2008 Jeep Grand Cherokee has a headlight aiming problem - the low beams are aimed too high. I cannot find the vertical aiming adjustment screws to fix the problem. Can anyone tell me how to adjust the low...


Hi, i have no idea if this will help you or not, but, on the 1997 grand cherokee, if you look at the headlight itself, look to the outer edge, over the top ontop of the headlight there is a white allen key hole, not sure on the size, this, basically is the up and down adjuster for the headlight, sorry if it doesn't help but i've just had to adjust mine, and thats where it is, the one towards the radiator is the in and out, it pushes or pulls the headlight offcentre

Nov 26, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Headlight pointing down, loose in housing


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 19, 2009 | 2008 Dodge Charger

1 Answer

2008 gmc sierra headlight adjustment for up and


did you use the numbers on headlamp lens for the headlight aimer

Nov 07, 2009 | 2008 GMC Sierra 2500HD 2WD

2 Answers

How do you make adjustments to a 99 bonneville headlights. Repairs were done to the front end and the headlights don't shine on the road now.


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 01, 2009 | 1999 Pontiac Bonneville

2 Answers

Replace highbeam 1996 rodeo


LIGHTING Headlights REMOVAL & INSTALLATION Non-Aerodynamic
Fig. 1: Replacing a sealed beam headlamp

bd06397.gif
  1. Disconnect the negative battery cable.
  2. Remove the front grille and/or headlight bezel.
  3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
  4. Before installing, spray some silicone grease into the bulb socket.
  5. Connect the wiring and install the bulb.
  6. Install the retaining rim and grille.
  7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.
Aerodynamic

Fig. 2: Replacing a headlamp bulb

cf46ef4.gif

Jul 24, 2009 | 1996 Isuzu Rodeo

1 Answer

Adjust headlights down


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Dec 03, 2008 | 2002 Nissan Xterra

Not finding what you are looking for?
2006 Pontiac G6 Logo

729 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...