Question about 1999 Jeep Grand Cherokee

1 Answer

Rear lights not working. Are the bulbs different in each of the 3 tail lights

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 97 Answers

Yes and check for corrosion on the sockets before you buy new bulbs

Posted on Nov 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The rear turn signals hazards and break lightsand reverse lights work but the tail lights will not come on why is this


The signal/ hazard and break light use the run on the same wire The backup light use a different wire and bulb. The tail light use a different wire Check wires and connections

May 31, 2015 | Cars & Trucks

3 Answers

If the break lights in my 1986 c corvette works but the tail lights do not, what could be the cause


Blown fuse ,bad headlight switch,or wiring issue.
the tail lights have there own fuse and are powered through headlight switch. Do the front running lights come on? If none of them work, switch could be bad if front work and rears dont, check bulbs and power to them when lights are on

Mar 17, 2015 | Cars & Trucks

1 Answer

How do i replace left rear brake light bulb


1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Oct 13, 2014 | 1999 Audi A4

1 Answer

Tail lights dont turn on


1. Replace your car tail light. You will need working gloves to protect your hand during the process. Of course you will also need a screwdriver, cleaning cloth, wire brush, and a good set of tail light bulbs.

2.Understand that different models of car have different set of tail light covers. Naturally, these covers will require different un-installation procedures. So, determine if you can dismount the cover from the outside or you will have to dismount it from the trunk of the car.

3.Determine how to dismount the tail light cover, carefully detach it from the car. You can use different sets of screwdrivers for this. Be careful not to break the tail lights cover. The important thing is you must be able to expose the bulb in order to extract it.

4.Remove the tail lights cover, unscrew the bulb from its socket. Sometimes you will have to press a little and twist the bulb in order to extract it from the socket.

5.Extract the bulb, bring it to your favorite auto parts and accessories store and find the exact match of your tail light bulb. Be sure to get the correct match because if you use other types of bulb, your tail lights may not work properly.

6.Reinstall the tail light bulb, clean the aluminum casing of the tail light. Wipe the socket and wiring with a dry cloth. You can use wire brush if there are corrosion around the tail light casing.

7.Put the good bulb on the socket. You might still need to apply a little pressure on the socket before you can install it fully.

8.Reinstall the tail light bulb, replace the cover of the tail lights and secure it tightly.

9.Test to make sure your new tail lights are working. Start the engine and apply the brakes. You can ask someone to see if the tail lights are really working.

resource: http://www.wikihow.com/Fix-Car-Tail-Lights

Aug 27, 2012 | 1998 Buick LeSabre

2 Answers

I have an 06 Dodge Charger. My rear passenger side turn signal isn't working. The bulb seems to be good because the tail light still works and it's the same bulb. What could be the problem here?


the turn signal and the brake light,, not the tail light section use the same filament, so be sure that the bulb is ok, have someone apply the brake,, if it goes on your bulb is fine and you have a different problem than the bulb , on the newer vehicles with the glass end on the bulb and the 3 wires ( sometimes 4 ) the wire gets smashed flat against the glass and doesn't make a good contact , remove the bulb and very gently pull the wire up away from the glass end, see if that works, if not, do the same thing to the socket end

Sep 03, 2011 | Dodge Charger Cars & Trucks

1 Answer

Right rear brake and signal light won't work. not the bulb. All other signals work and front right works.


first eliminate the possibility that you have the wrong bulb in the wrong socket. it sounds dumb but going way back to 1157 bulbs there have been two rear tail light bulbs which will fit into the same socket but are electrically different. If you have ever driven down the road following a car which had one bright and one dim tail light, or brake light, then you have seen this in action.

since you have one good tail light assembly remove the bulbs, taking great care not to mix them up and make sure the bulbs are exactly same as in the non working assembly. i mean you have to look closely at the bulb's connection points as they will look very much the same.

if the bulbs are correct then you are looking at buying a new socket, or light assembly if the whole thing is wired into the car.

May 21, 2011 | 2005 Ford Freestar

2 Answers

Rear tail lights


Yes, The tail light works on a different part of the bulb than the brake light. That bulb has a burned out tail light filiment. Needs to be replaced.

Nov 12, 2009 | 2002 Dodge Ram 3500 Truck

1 Answer

How do you replace the tail light bulbs on a 2006 Pontiac Vibe


Tail Lamp: Service and Repair
TAIL LAMP REPLACEMENT
REMOVAL PROCEDURE
1. Open the rear compartment lid.
2. Remove the rear compartment trim panel (4).
3. Disconnect the tail lamp electrical connectors.
4. Remove the following components from the vehicle:
- The 3 nuts (3)
- The tail lamp (7)
5. Remove the following from the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
6. Remove the following from the lamp sockets, if necessary:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
INSTALLATION PROCEDURE
1. Install the following to the lamp sockets, if removed:
- The stop lamp bulb (1)
- The turn signal lamp bulb (6)
2. Install the following to the tail lamp:
- The stop lamp socket (2)
- The turn signal lamp socket (5)
3. Install the tail lamp (7) to the vehicle. Secure the tail lamp (7) with the 3 nuts (3).
NOTE: Refer to Fastener Notice in Service Precautions.
Tighten the tail lamp nuts to 10 N.m (89 lb in).
4. Connect the tail lamp electrical connectors.
5. Install the rear compartment trim panel (4) to the vehicle.
6. Close the rear compartment lid.

Oct 30, 2009 | 2003 Pontiac Vibe

1 Answer

How do you wire up a trailer harness to a 1999 Grand Voyager?


Your earth is bonding properly. Make sure you have a good bond that is fixed either to your chassis, with all rust, sealent and other cotings are removed frois should dolve your problem.m the fixing. Th

Jul 25, 2009 | 1996 Chrysler Town & Country

1 Answer

Tail break lights don't work. Window break light does work however. Bulbs have been replaced.


Check the brake light fuse. The high mounted brake light (third brake light) is on a different circuit than the brake lights. Hope this helps.

May 23, 2009 | 1998 Mercury Mystique

Not finding what you are looking for?
1999 Jeep Grand Cherokee Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...