Question about Chevrolet Malibu

Open Question

I need a diagram for an exhaust system for a 1999 chevrolet malibu

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

StormStrikes
  • 104 Answers

SOURCE: 1999 chevy malibu

That engine does not have a timing belt, it has a timing chain and therefore much easier to work with as it can only go on a certain way, the primary focus being getting the dots on the timing chain sprockets lined up properly.

I believe, with the engine at Top Dead Center on cylinder #1, the dots will be facing each other. That is to say, the do on the cam sprocket will be facing the dot on the crank sprocket.

Posted on Jan 02, 2009

theroadis
  • 81 Answers

SOURCE: Change headlamp on a 1999 chevrolet malibu

The headlamp assembly on each side comes out as a unit. Raise the hood. Remove black plastic cover that hides the assembly. This is done by prying up on the plastic tabs on the cover that hold them in place. (They look like inserts) Once you pull up on the center portion of tab, the whole fastener comes out. Once the cover is out of the way, you will see these square black (about an inch Sq.) horizonal plates of which are connected to ball like fixtures (ball and socket) you pull up on the plates which release the ball to come out of the socket. The headlight assembly will swing out at the top, then raise straight up once it clears top. The headlight bulbs will now be accessible. Turn light bulb socket (with the wiring) counterclockwise 1/4 turn to remove. replace bulb. wipe clean with paper towel or cloth before reinstalling, as acid from skin or other contaminates will destroy bulbs. reinstall in reverse.

Road

Please rate me so I know if I helped.

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: how to replace timing belt

1999 chevy malibu 6 cyl dosen't have a timing belt just the serpentine drive belt the routing diagram should be under the hood

Posted on Aug 14, 2009

ZJLimited
  • 17970 Answers

SOURCE: looking for the serpentine belt diagram for a 1999

1999 CHEVROLET MALIBU - V6 3.1L 189ci GAS FI N J
Belt Routing Diagram Multiple Accessory

22e74d7.jpg

Hope this help (remember comment and rated this).

Posted on Mar 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Chevrolet Malibu veci label I like diagram.


there was one posted her not long ago,, check this link, http://www.fixya.com/cars/t4253333-find_diagram_99_chevy_malibu you might need to copy and paste that to a word doc, so you can enlarge the print to view it better

Sep 12, 2011 | 1999 Chevrolet Malibu

1 Answer

99 chevy malibu serpentine belt diagram


There are 2 possible diagrams for your car depending on which engine it has. Both diagrams are listed below:


1999 Chevy Malibu 2.4L
greg_margo_28.jpg





1999 Chevy Malibu 3.1L

greg_margo_29.jpg

Aug 16, 2011 | Chevrolet Chevy Cars & Trucks

1 Answer

I need a diagram for the routing of serpentine belt on a 1999 chevy malibu.


If you open the hood and look on the frame (usually just near the hood latch) there should be a diagram there for you. It might also be on the underside of the hood itself.

Jul 16, 2010 | 1999 Chevrolet Malibu

1 Answer

Where is the thermostat located this is a 1999 chevrolet malibu with a 2.4 engine.


Hi,


The thermostat for this model is located underneath the throttle cable assembly, behind the exhaust manifold.


Thank you !!

Jul 04, 2010 | 1999 Chevrolet Malibu

1 Answer

Change oxygen sensor 1999 chevrolet malibu


First locate it and get a wrench and unscrew it from the exhaust pipe and unplug it from the wiring harness and re-install the same way.

Jun 02, 2010 | 1999 Chevrolet Malibu

2 Answers

Looking for the serpentine belt diagram for a 1999 chevrolet malibu 3.1 l


1999 CHEVROLET MALIBU - V6 3.1L 189ci GAS FI N J
Belt Routing Diagram Multiple Accessory

22e74d7.jpg

Hope this help (remember comment and rated this).

Mar 31, 2010 | 1999 Chevrolet Malibu

1 Answer

How to replace timing belt


1999 chevy malibu 6 cyl dosen't have a timing belt just the serpentine drive belt the routing diagram should be under the hood

Aug 02, 2009 | 1999 Chevrolet Malibu

1 Answer

Starts then shuts down


You may have a clogged up exhaust, I had this problem on several occation that just about drove me crazy thinking it was electrical problem. Unbot the exhaust, and see what happens. The catalytic converter usually is the one that clogs up so you want to disconect the exhaust system before the catalytic converter.

Jun 30, 2009 | 1999 Chevrolet Malibu

1 Answer

Need intake manifold assembly diagram


Hi, i have posted a link to the diagram(exploded) below.


INTAKE DIAGRAM(EXPLODED)


Please rate and have a great day:)

May 20, 2009 | 1999 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...