Question about 2005 Hyundai Accent

1 Answer

Replace lecence plate light on 2005 hyundai accent

How do I replace licence plate light on 2005 hyundai accent

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,197 Answers

A slightly better set of instructions might help you. Mine is a 2003 Accent. You have to remove the access panel that covers the lamps and the wiper control. Remove the phillips screws along the bottom of the panel (closest to the floor of the trunk when the lid is closed). Then remove the two screws that hold the brackets onto which the two strings are linked which are used to raise the rear deck slightly when the trunk opens. Next, there is a small cover underneath the rear wiper (about 2 inches square) that you need to carefully pry off using a small flat head screw driver via the indents on the lower side of the plastic cover. Inside you will find a 10mm bolt; use a ratchet to remove the bolt. Next, using a small flat head screw driver, carefully pry the middle section of moulding between the panel you are removing and the molding that covers the top portion of the back glass. There are two clips at the base of each middle moulding piece closest to the panel you are removing. Once those pop free, grab the panel at the bottom and firmly but gently pull away from the car body to pop free the two retaining clips holding the moulding to the car body. Finally, use one hand to grasp the panel from the bottom and the other to help help slide the panel "up" towards the glass (top of the car). The panel's top is flanged, and must slide up and away from the lip on which it sits. With the panel removed, grasp the white socket that holds the bulb and with gentle pressure turn it counter clockwise about 40 degrees and then pull the socket out. The replacement bulb is a type 168. Reverse these instructions to assemble, making sure in the end to push all retaining clips back into place until you hear them "catch" and hold the panel firm;y against the car body so that you do not get vibration noise.

Posted on Nov 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will the clutch plate out of a 1998 Hyundai Accent fit in a 2005 Hyundai Accent? As well as the Slave cylinder?


go to a spares shop and see if the part numbers are the same
I feel that it will be the same but due to the vagaries of engineering you have to check first
are you positive that it is the clutch as a faulty master cylinder will cause the plate slip giving the same indication as a failing clutch

Sep 04, 2016 | Hyundai Accent Cars & Trucks

1 Answer

2005 Hyundai Accent Check Engine Light


Did you reset?fill up a tank and reset, and see what happen.

Aug 23, 2016 | 2005 Hyundai Accent

2 Answers

How to remove the dome light assembly from a 2008 accent


It literally just pulls out, it's only held in via clips. I had to replace mine as well

Mar 06, 2015 | 2008 Hyundai Accent

2 Answers

Dead dome light


dead dome light could have blowed bulb.

Jan 24, 2012 | 2008 Hyundai Accent

1 Answer

How to get to licence plate bulbs on a 2006 accent


Go to www.hmaservice.com and register your vehicle by VIN #.. you'll then have access to wiring diagrams, shop & owner manuals, service bulletins, campaigns, illustrations and procedures, etc

Sep 03, 2011 | Hyundai Accent Cars & Trucks

1 Answer

Engine light on 2005 Hyundai accent


Engine Light 'ON' is a warning light from the inbuilt system. As far as your car is driving good, no need o worry about the light.

This is from the electronic control unit signal. This can occur due to some sensor performance present in the engine. Take it to the nearest dealer. They have a diaganosis unit to fix it easy.

Jun 05, 2010 | 2005 Hyundai Accent

2 Answers

Replace licence plate bulb 2003 accent hatchback


open boot and locate bulb holder inside boot lid. gently squeeze the clips to release the holder and push out the holder gently. replace bulb, and push holder back in.

Mar 08, 2010 | 2003 Hyundai Accent

1 Answer

Changing licence plate light on a 2005 hyundai accent. Idont know how this web site really works i i need help


There are only two ways to access a a bulf. By taking the lens off the front, or removing it from the back. The lens would be fastened with screws, if no screws in lens, check the back of the fixture for a socket which rotates and pulls out.

May 02, 2009 | 2005 Hyundai Accent

1 Answer

How do I change the license plate tag lights in 2005 Huyndai Accent?


remove the inner panel of boot lid to access rear of No plate light assy ? then the 2 x bulb holders are twist anti clockwise and lift out of each lamp replace bulbs and reassemble

Jan 19, 2009 | 2005 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...