Question about 1998 Isuzu Trooper

1 Answer

How can i replace my r/front axle c.v boot on my 2001 isuzu trooper 4X4

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,702 Answers

This is a realy big job you need to strip out the 4 wheel drive hub just to get to the wheel bearings,,, not some thing for the novest to even try to do,,,best thing is to get a book on it first, after you have striped out the 4 wheel drive hub and took off the wheel bearings and disk (rotor) you still need to push the drive shaft through the hub and thats very hard as well, and you got to pop off top and bottom swivels,,,and finaly you can get to the rubber boot,,,,,all £3.50 of it!!!! but £250 just to get to it? try sticking a push bike patch over the split,,,its far easer and quicker

Posted on Nov 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1996 3.1 d trooper wont engage 4x4


A lot of these troopers had a module on the side of the transfer case that put the unit into gear. They go out fairly often. Also check the solenoid on the front axle that engages the front axle as they are another problem that will cause the front axle not to engage

Jan 09, 2015 | 1996 Isuzu Trooper

1 Answer

I can feel my trooper shift into 4x4 but I'm not


I had this happen on my 94 automatic. 4x4 "engages" but no power to front wheels. One of the front axles went bad so the 4x4 doesn't engage on either front wheel. It was a $800 fix.

Feb 01, 2012 | 1994 Isuzu Trooper

1 Answer

Trying to remove the rear axle to replace seal from a 2001 Isuzu Trooper. It doesnt want to come off..what do I do?


Remove bolts and get a slide axle puller, then take it to a machine shop all of the parts to fix it.

May 01, 2010 | 2001 Isuzu Trooper

1 Answer

CV axle removal 1999 Isuzu Trooper


The easy way is to take the inner boot off and take the joint apart. Take new cv axle apart at inner joint and attach to the old one sticking out of axle housing. You will need to get new boot clamp.

Mar 03, 2010 | 2003 Lincoln Town Car

1 Answer

Front drive shaft removal for 2001 izuzu trooper 4x4


Under the rubber boot inside the CV joint is a big spring clip round the edge , take this out and then the shaft pulls away from the axle with the CV on it .If you are fitting a new boot cut the old off if not just get the clips off and pull the boot back.

Did you take the shaft out from the wheel hub end too ?

Oct 04, 2009 | 1988 Isuzu Trooper 2 Door

1 Answer

Change a cv boot on a 1996 isuzu trooper


First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Sep 28, 2009 | 1994 Isuzu Trooper

2 Answers

How do i remove cv axle for a 98 isuzu trooper


Go to my profile I have just explained how to change a cv boot on a Trooper. The axle needs to be taken out to change the boot so the same solution. What you call an axle I have refered to as a drive (short for driveshaft) It takes a lot of explaining so save me a lot of writing if you read the solution I gave for changing the CV boot. Cheer's

Sep 27, 2009 | 1998 Isuzu Trooper

1 Answer

Cv joint replacement 1998 isuzu trooper 4x4


This is a simple job that is why it is not very detailed in your book. Nothing special. Do one side at a time so you have a reference to how to reassemble it. Remove your tire , brake calipers be sure not to stress the rubber brake lines or open the brake lines to air. Remove both upper and lower ball joints. When taking out the ball joints remove the cotter pin and bolt and beat the **** out of the joint for it to release. Then the C/V axles will come right out with a bit out encouragement. You will need a few tools wrenches pry bar hammer. I would buy a Chilton's or a Haynes repair manual for torque specs for reassembly. Good luck and take your time. And unless the axles are making noise you can just replace the rubber boots. Which is alot cheaper.

Jun 01, 2009 | 1998 Isuzu Trooper

1 Answer

Removing half shaft from 2000 isuzu trooper


must remove clips from inside front axle housing!! If the cv joint aint broke DONT FIX IT the boots can be replaced in less than 1 hour with hand tools and the boot is around 20$ at any parts store

Mar 31, 2009 | 2000 Isuzu Trooper

2 Answers

2001 Trooper: Front axle will not engage when I press dash 4x4 switch


hi guys i would check all the small vacume pipes that conect the sol valves toi the vacume actuators having just replaced the engen in mine i found that these do not have any clips holiding them on tight and can get oil on them and become oversized and leak you can test the diaframes in the actuators by putting a length of pipe on one port and sucking by mouth you can hear the actuator move and then find you can put toung on end of pipe and it will hold a vacume if it does not then chances are the actuator diafram id u/s hope this helps bill

Nov 09, 2008 | 2001 Isuzu Trooper

Not finding what you are looking for?
1998 Isuzu Trooper Logo

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...