Question about 1999 Dodge Durango

1 Answer

Dodge durango rear breaks are locking easy. Fronts look good, blead the fronts and they work good, the rears are clean no leaks.. just applying, and the rears lock.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Well, first off Dakota and Durango are known for their over sized rear brakes, but does not usually cause them to lock up. My guess is, the master cylinder is faulty. They are relatively cheap and easy to replace, and would be the next logical step, if the brakes them selves look good.

Posted on Nov 15, 2009

Testimonial: "Great simple and to the point, thank you very much"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The rear locks dont work with my key pad nor with the unlock button in the front but the fronts locks work


Not sure the rear make or model of this car but this sounds like you may have bad lock actuators, these are the small motors that lock and unlock the door locks. there is one in each door. good day,

Mar 23, 2012 | 2008 Chevrolet Impala

2 Answers

I recently had my truck--a 2006 GMC Canyon inspected for brakes because there was a squealing noise occasionally when I applied brakes. I had it inspected and the technicians said that I should have my...


hi sounds like good advice with out your rear brakes working properly all the load will be transfered to the front brakes causing uneven braking and in wet or slippery conditions front wheels will start locking up causing lose of control

Sep 13, 2011 | 2006 GMC Canyon

1 Answer

WE HAVE A 1998 DODGE DURANGO AND AS SOON AS YOU TURN THE HEADLIGHTS ON THE TAIL LIGHT FUSE BLOWS,COULD YOU PLEASE GIVE ME SOME HELP..


TRYchanging all rear tailite bulbs, dont work your fronts , or disconnect all fronts and rears tail and marker and plug in one at a time till it blows fuse you'll know which side and wire bad or check your trailer wiring and trailer wires where they meet factory wiring.It's blowing the fuse means short to ground(over current)

Aug 07, 2011 | Dodge Durango Cars & Trucks

1 Answer

1996 Nissan Quest GXE model. Bleeded brakes. No parts replaced. Brake works normally. No drag. With ABS. Now, right rear wheel and left front wheel locks. left rear wheel and right front wheel turns...


you need to first adjust rear brakes per TSB in our file, 98-14=4 I think. (If you replaced or adjusted rear brakes)

Then bleed again, but you may need to loosen the pressure valve on the master cylinder, or apply very hard pressure on the dowm stroke with the front bleeder on the claiper open just slightly. You have to overcome the the valve spring in it as it is deisgned to send pressure to the rears before the fronts to allow the rears to engage at the same time as the fronts. It takes higher pressure on bleeding to over come.

go here for help

http://groups.yahoo.com/group/villagerquest/

Dec 13, 2010 | 1999 Nissan Quest

1 Answer

1999 durango the abs light and brake light comes on about 3 or 4 times in the past week as im driveing and then goes off in a few minutes i have new brakes and roters on the front and only rear wheel abs,...


did you check the speed sensor on the rear end on top of the rear end. this sensor works the speedometer the abs and break lights and power door locks

Aug 30, 2010 | 1999 Dodge Durango

1 Answer

2001 dodge durango..rear air not working, front


u could have bad control modular,,have him ck that,,

May 28, 2010 | 2001 Dodge Grand Caravan

1 Answer

Brake pad replacement


You will need to bleed all four corners, starting at the right rear, then left rear, then right front, then left front. Your bleed procedure always goes from the wheel farthest from the master cylinder, to the closest. By bleeding only the rear brakes, you've gotten air out back there, but not necessarily any air that might have moved farther forward. Bleed your rears again, and then move forward to bleed the fronts, and see if that helps.

Aug 31, 2008 | 2003 Audi A4 Cabriolet

Not finding what you are looking for?
1999 Dodge Durango Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...