Question about 2004 Chrysler Sebring

1 Answer

Passengerside axle bad How do I replace it. - 2004 Chrysler Sebring

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 832 Answers

This could be a heavy job for you. You will be needing
some heavy tools to get it off. It it recommended, that
you get the services of a car repair center. In this manner, you can be sure of their guaranted services.

Posted on Nov 15, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

Clicking noise down by the front tires.


check your axles, for an open cv boot, this clicking is on straigth or turning, if turming to your rigth you hear noise to be louder on your left then your left axle is bad, do the same to your left and if noise exists then your rigth axle is bad.good luck

Feb 27, 2011 | 2003 Dodge Caravan

1 Answer

1997 plymouth voyager speed control sensor


the sensor is located on trany on the passengerside, if you follow the pass/side axle to trany then look atop of trany and you will see sensor, remove the one bolt holding it and wiggle and twist while pulling it up and out, theres a electrical connection that you will also have to unplug.

Aug 20, 2010 | Plymouth Voyager Cars & Trucks

1 Answer

Replace passengerside headlamp


you have to remove the grille and take a look at oyur new one and it will be pretty obvious how it is attached

Apr 18, 2010 | 2006 Chevrolet Trailblazer

1 Answer

E180auto passengerside aircon always blowing cold 1992 model


Sounds like the vent control motor is bad. It controls how much hot water flows through the heater core. OR the heater core for that side is clogged

Feb 03, 2010 | 1991 Mercedes-Benz E-Class

2 Answers

I replaced my 02 sensor and cleared the code po 155 still comes on on my 2002 sonoma please help


which sensor did you change, the correct one is located on passengerside on exhaust pipe near the top. not after the converter or on the driverside, that truck if it has a 4.3 v-6 engine it has 3 to 4 sensors located 2 before the cat and 1or 2 after the cat, you want the one on passengerside closest to the top near manifold. hope this helps.

Jan 04, 2010 | 2002 GMC Sonoma Extended Cab

3 Answers

How to adjust parking brake on a GMC Sierra 2500 HD Duramax 4wd?


The adjuster is just like on a car with drum brakes. It can be adjusted with the wheels still on the truck, but if yours is out enough that it doesn't work, an inspection is warranted. Axle seal failure is common and will soak the shoes.

Jacked both rear wheels off ground, and while slowly spinning wheel, tighten the star-wheel adjuster until you just hear and feel brake drums rubbing, then loosened slightly.
There's a plastic dust cover about 1/4" X 1" that you remove, and use a drum brake adjuster tool.

The driverside access hole is below axle, easily accessable. To tighten driver side rear parking brake, turn star-wheel adjuster down.


The passengerside access hole is found above axle, and difficult to see. Removed pass side wheel and used an inspection mirror.
To tighten passenger side rear parking brake, turn star-wheel adjuster up.

Good luck and hope this helps. Oh and the other thing to is that if you do smell axle fluid around the wheels and see oil leaking from the drum area. Then you have a axle wheel seal and or bearing gone bad too.

Apr 13, 2009 | 2002 GMC Sierra 2500HD

1 Answer

How to replace bearing


There is a vacum switch in the transfercase on the drivers side. you can get to it with a wrench, but it will make you work for it. Part store is like $45.00 GM like $90.00, Same part.
Rear bearing. remove the differental cover and drain fluid. Remove the C Clip that hold the Axle in. Slide the Axle out and inspect to see if you need a new one. High mile axle has a worn grove where the bearings are and changing the bearing alone does nothing. You ight get away with a finding a bearing to match your axle if it's worn. 
Remove the oil seal and then the bearing from the axle tube. 
In-stall in revers, note use lots of lube on the seal and be careful not to nick the seal and bearing. 
Fill differental with oil and run around the block, not hard and re-check the fluid. May want to go with syntetic oil or add lucus. Less maintance of oil changes to differental.
Good luck and hope this help.

Apr 03, 2009 | 1994 Chevrolet S-10 Blazer

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8547 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...