Question about 2002 Mercedes-Benz C-Class

Open Question

Mercedes C220CDI ignition stuck

Mercedes C220CDI ignition lock not disengaging, therefore not allowing me too start

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
redbeard00
  • 957 Answers

SOURCE: Key stuck in ignition of 1976 chevy corvette stingray 350 auto

If I understand, the key will not rotate to all of the normal positions? If this is true, then I would guess that the trani didn't fully return to the park position please verify, You can check the ignition switch(the one that is half way down the steering column) for defects. Is there any binding, does the rotate freely? Thank you; good luck.

Posted on Apr 25, 2009

Ad
  • 12 Answers

SOURCE: my jeep wont lock into park therefore the key is

there is an interlock solenoid that allows the key to come out in park near the shifter that is most likely bad

Posted on Mar 19, 2010

c1apton15
  • 3400 Answers

SOURCE: Mercedes c220cdi does W or S position make

W is winter and it starts in a higher gear to prevent slipping when accelerating. S is standard. Standard is better for fuel economy.

Posted on Mar 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is mr in actros


The MR code comes up because you are not allowing the vehicle to do the self checks before trying to start engine, it therefore does not regognise the key in the ignition and the immobiliser is activated. to overcome this allow the vehicle to do its self checks and when the neutral N symbol is shown then turn ignition switch to start.

Jan 27, 2012 | Mercedes-Benz Mercedes Bentz Actros Semi...

1 Answer

Mercedes c220cdi does W or S position make different in fuel consumption


W is winter and it starts in a higher gear to prevent slipping when accelerating. S is standard. Standard is better for fuel economy.

Mar 12, 2011 | 2004 Mercedes-Benz C-Class

2 Answers

I am stuck in park and cant engage drive. my fluid levels are normal. engine is on. footbrake is depressed. steering lock is disengaged. ticking noise in steering column when button on gear shifter is...


You need to have the dealer check the inter lock solenoid on the shifter cable,
It is powered by the ignition and brake light switch,pushing the brake releases the solenoid and allows you to move shifter.

Dec 19, 2009 | 2001 Pontiac Aztek

2 Answers

Need to change the Clutch Pedal Ignition Switch; do you have instructions how to do this?


Removal & Installation
  1. To prevent accidental air bag deployment, disconnect the negative battery cable, then the positive battery cable to allow residual energy in the air bag system to drain.
  2. Remove the steering column shroud(s).
  3. Disengage the wiring harness connector from the ignition switch.
  4. Insert the key into the ignition switch, then rotate the ignition key lock cylinder to the RUN position.
  5. Remove the two screws attaching the ignition switch.
  6. Disengage the ignition switch from the actuator pin and remove the switch.
To install:
A new ignition switch purchased from Ford will already be set in the RUN position.
  1. Adjust the new ignition switch by sliding the carrier to the RUN position.
  2. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  3. Install the ignition switch onto the actuator pin.
  4. Align the switch mounting holes and install the attaching screws. Tighten the screws to 50-69 inch lbs. (6-8 Nm).
  5. Attach the electrical connector to the ignition switch.
  6. Connect the positive, then the negative battery cables. Check the ignition switch for proper function in START and ACC positions. Make sure the column is locked in the LOCK position.
  7. Install the steering column shroud(s).
Is this the one you are asking about?

Dec 07, 2009 | 1995 Ford Mustang

1 Answer

MB C220cdi. epc light has come on?


epc light come on my screen the engine is not start pleas solve this problem

Nov 12, 2009 | 2001 Mercedes-Benz M-Class

1 Answer

2001 Mercedes clk230 infrared key wont turn in ignition


a the problme is that the ignition is glued shut. i am a mechanic i see these thing every DAy.






thanks DING!

Apr 25, 2017 | 2000 Mercedes-Benz CLK

3 Answers

How do reset the FSS after Service a and Service b


The instructions for resetting the FSS are almost correct for a 2007 C350.
Change line 1 to read:
1 Turn electronic key in the steering lock to position 2

I would also increase the hold times to 5 seconds.


Aug 09, 2008 | Mercedes-Benz CLK Cars & Trucks

2 Answers

Key stuck in ignition??


Try replacing the ignition switch.

Jun 26, 2008 | 2003 Mazda MPV

Not finding what you are looking for?
2002 Mercedes-Benz C-Class Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...