Question about 1986 Renault Sport

1 Answer

Hi there i've just done my renualt clio 1.4 drive belt, but not sure the corret position of the belt. it looks there are three different positions have which one would it be could you please explain many thanks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Renault Master
  • 22,095 Answers

Do you mean timing belt ,1.4 petrol .

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tapping noise


Have the cam followers checked . Have the rocker shafts and bushes checked for wear . have a compression test done as there may be a loose valve seat insert.

Mar 08, 2014 | Renault Cars & Trucks

2 Answers

Hello i have a 1998 (s reg) renualt clio grand


how did the oil cap fall off and not get lost? check that the cap doesnt fall off again. if you didnt drive with an engine empty of oil, then everything will be fine.

Nov 03, 2013 | Cars & Trucks

1 Answer

1998 ford escort altinator two bolt or three bolt? engine light is on brand new battery and the battery light is on . car just died when driving waited 7mins and it started .is it the altinator


check with volt meter. 12 volts with engine off. Should be 14 volts with engine running if alternator is working.
First, clean battery posts and cable ends. Then check owner manual for fuse locations and blown fuses. There is a large 100 amp fuse in box under hood.

Is the battery lamp lit on the dash?

Looks like 3 bolts. please rate when done

SECTION 414-02: Generator and Regulator 1998 Escort/Tracer Workshop Manual
REMOVAL AND INSTALLATION Generator -Sedan and Wagon Removal
  1. Disconnect the battery ground cable.
  1. Remove the generator drive belt.
    1. Release the tension on the drive belt.
    1. Remove the drive belt from the generator pulley.
  1. Disconnect the HO2 sensor harness clip from the generator bracket.

  1. Position the generator bracket aside.
    1. Remove the A/C line bracket bolt.
    1. Remove the power steering pressure line bracket bolts.
    1. Remove the generator bracket bolts.
    1. Position the generator bracket aside.
  1. Remove the generator bolts and position the generator aside.
  1. Remove the generator.
    1. Disconnect the two generator electrical connectors.
    1. Remove the battery positive nut and washer.
    1. Disconnect the battery positive cable and remove the generator.
step 4
snorkelbobby_37.gif

Feb 12, 2011 | 1998 Ford Escort

2 Answers

Diagramm serpantine belt 2005 sprinter2500


Hi.

Here the belt routing for 2005 Dodge Sprinter 2005, whch was sold only with the 2.7 engine mounted:



feac688.jpg


Fig. Accessory Belt Routing-A/C Compressor (1), Power Steering Pump (2), Tensioner (3), Crankshaft Pulley (4), Water Pump (5), Alternator (6), Idler Pulley (7)-All Engines

Here a different view:

62bcecc.jpg

Here also the fan belt routing;

729c6e0.jpg

Fig. Fan belt routing-Fan pulley (1), Fan belt (2), Crankshaft pulley (3)-3.0L engine shown

PROCEDURE Removal & Installation


2.7L Engine

1. Loosen the tension adjust and remove the A/C compressor drive belt.
2. Attach a 3 / 8 inch drive ratchet to the automatic belt tensioner.
3. Rotate the belt tensioner counterclockwise to release the belt tension.
4. Remove the accessory drive belt, starting with the water pump pulley.



To install:

1. Position the accessory drive belt around every pulley except the water pump pulley.
2. Rotate the drive belt tensioner clockwise, install the accessory drive belt and release the tensioner.
3. Position the A/C Compressor drive belt over the crankshaft pulley and A/C compressor pulley.
4. Tighten the drive belt tensioner.
5. Ensure the belt is seated properly on all of the pulleys.

If this solution was helpful, then please do not forget to Accept.
Writing dedicate solution, sharing skills, researching and extracting info from service documents takes time, and your feedback is important for us.
If you repute any solution useful, please click on Accept.

All the best.

Ginko.

Sep 21, 2010 | Dodge Sprinter Cars & Trucks

1 Answer

I bought a 2000 w reg renualt kangoo, engine was done so i got a clio engine of same year same size.now that engine is changed i cant get a spark 2 engine.ecu ? or wot


immobilizer.you need the key and barrell from clio engine and the ecu or else bring to dealer to reprograme the ecu to the key

Apr 07, 2010 | 2000 Renault 181

1 Answer

Can you tell me the cam timing for mk 1 renault clio 1.4 m reg thanks petrol 1994


the cambelt timing marks for clio 1.4 are = the crankshaft cog alignes withmark at 6 o/clock position at TDC No 1 cyl and the cam cog alignes with mark on cyl head at rear of cog at 12 o/clock position belt is fitted anti clockwise from crank then w/pump and then cam cog hope this helps ?

Jan 13, 2010 | 1986 Renault Sport

5 Answers

Clio 1.2 W reg


try my last solution posted, connectors on renault clios renouned for corroded electrical connection car guaranteed to start unless car needs replacement loom these also prone to fail very bad design of wiring connections they did a better job in the 70s

Aug 09, 2009 | 2000 Renault 181

1 Answer

I have a renault clio 1.4 R reg it misfires


misfire could happen if you have a leak in the intake or exhause valve , or if your engine running rich thats mean too much fuel coming to the engine . you should check oxygen sensor

May 31, 2009 | 2005 Renault 181

2 Answers

How long can you expect Renualt Clio Brake Disc's to last


They should last at least 50000 miles. In some areas where salt brine is used this woul be reduced.

Mar 12, 2009 | 1986 Renault Sport

2 Answers

I need a copy of teh manual for my 2004 Ford Explorer manual.


Wear your safety belt, or simply unplug the harness located at the seatbelt receptacle.

Jan 13, 2009 | 2004 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Renault Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

xxxxxx xxx

Level 3 Expert

4834 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Are you a Renault Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...