Question about 1994 GMC Jimmy

1 Answer

Can't get oil filter off, can i put vice grip on inside stem?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 399 Answers

Hi use a chain grip on the outer case and make sure you remove the old rubber seal ring and replace it with the new one good luck

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have tried everything I know to remove a stripped oil drain plug. Any ideas?


is the head stripped or threads stripped if head grind down to next size or rectangle for wrench or vice grip if threads better to drop the pan to inspect for filings as well as easier removal of plug

Sep 22, 2016 | 2007 Dodge Ram 1500 Quad Cab Sport

1 Answer

My dipsticktube is broken off about tow inches above the motor. it a 93 s-10 with a 4.3. how would l remove it?


If the remaining part of the dip-stick tube is oil soaked. It should pull out easily. Take a small screw or bolt and slide it into the tube. The bolt must fit inside snug (don't use one that will drop down and inside the pan). At the bottom of the tube, wet it with penetrating oil (to break up the rust). Then attach the vice-grips to the tube. The bolt or screw is to prevent you from crushing the tube. Gently rock the vice-grips back and forth, to break the tube loose from the engine block. Don't be too rough, you don't want to break the tube flush. If you are unsuccessful, remove the vice-grips and with a small hammer and flat chisel. Gently tap the bottom of the tube. Don't cut through it, the goal is to try to break the rust inside loose. After a few taps, reconnect the vice-grips and try again. you may need to repeat 6-12X so be patient. Please let me know about your progress and if you have other questions, good luck.

Mar 17, 2014 | Cars & Trucks

2 Answers

Bolt is stripped can get off tried penetrating oil didn't work need help


I would use a vise-grip that fits really snug and you should be able to break it loose. You will want to replace the bolt so you don't have this problem again

Mar 02, 2013 | Cars & Trucks

1 Answer

E BRAKE IS STUCK!!!


the cable is stuck in the sleeve, lots of penetrating oil and grip the wire cable with vice grips and tap it back with a hammer, good idea to get it replaced

May 24, 2010 | Ford Escort Cars & Trucks

3 Answers

Plug was overtightened .. subsequently stripped .. took it in for an oil change & they tried a vice grip on the plug .. no movement but bolt head is gone . I need remobe the plug .. I have a new...


They should have never used a vice grip. You always use a socket on any hard to remove bolts because it provides equal force around the entire bolts. Vice grips only grab two sides.
You can try a bolt extractor, you can purchase them at Lowes and other places.
If it doesn't work, you will need a new oil pan.
Stop going to the place(s) that put it on too tight, and tried to take it off with vice grips.

Feb 27, 2010 | 2004 Chrysler Pacifica

1 Answer

I want change the air filter and oil filter. How do I do that and is their any special tool need for each area?? I have a 2007 volkswagen passat/4 door


hey
No there's no specific special tools required, you can buy oil filter removal tools which are usually a chain that is rapped around it to get grip or a claw type thing. Try to loosen it with your hand first and if that doesn't work you could use a fan belt and vice-grip's or buy a removal tool. the air filter is just a matter of flicking if a few clips.
good luck

Dec 30, 2009 | 2007 Volkswagen Passat Sedan

2 Answers

How to remove a strippped oil change nut on a 1997 Mazda Protege


use vice grips they lock on tight or a pipe wrench [plumbers] as the harder you pull the tighter they grip!
Remember its anti clockwise to undo the plug!
& somtimes its a good trick to tighten the nut just to break the toque seal! then it can be undone!
Cheers Rob

Jun 30, 2009 | 1997 Mazda Protege

1 Answer

2005 pontiac sunbird oil filter location


Your looking for the location of your oil filter on your 2005 Pontiac Sunfire. They use a fabric/paper file which is located on the top/front of your engine. If your vehicle has an Ecotec engine, then open your hood. stand directly in the center of your car looking toward the windshield. And when you look down, it's at the front of the engine over to the right a bit. You need a certain tool, or Vice grips to turn the large plastic shaped cover off (Counter clockwise to losen). When it is loose, and you take off the cap. the oil filter will come out with it, you pull it off, and replace it with a new one.

Apr 18, 2009 | 2007 Chevrolet Cobalt Coupe

1 Answer

Oil filte removal


If you are disposing of old filter complete and replacing with completely new filter then drive a medium size screwdriver through the side of the body of the filter,till it pokes through the other side then turn the screwdriver to unscrew the filter.Or you can purchase a pair of vice grips with a chain head at any hardware store.

Dec 16, 2008 | 2005 GMC Envoy Xl

Not finding what you are looking for?
1994 GMC Jimmy Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...