Question about 2000 Toyota 4Runner

1 Answer

Regarding Shock installation. I was watching when they were installed and I noticed they installed only one bushing not two like the picture on the Monroe sensatrac diagram shows. Could this be causing the clicking noise?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

I WOULD THINK THAT IS WHAT IS MAKING THE NOISE AND I WOULD ALSO TAKE IT BACK AND HAVE THEM DO IT THE RIGHT WAY

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO YOU REMOVE THE SUPPORT TO FRAME BOLT ON THE REAR SUPPORT ASSEMBLY ON A PONTIAC TORRENT


Shock Absorber Replacement
Removal Procedure
Raise and support the vehicle. Refer to Vehicle Lifting
Remove the lower shock bolt.
For right side only, remove splash shield.
Remove the upper shock bolt.
Remove the shock from the vehicle.
Installation Procedure
Install the shock to the vehicle.
Notice: Refer to Fastener Notice in Service Precautions.
Install the upper shock bolt.
Tighten the bolt to 110 Nm (81 ft. Lbs.).
For right side only, install splash shield
Install the lower shock bolt.
Tighten the bolt to 110 Nm (81 ft. Lbs.).
Lower the vehicle.


For complete step by step guide with diagrams click the link below:
http://carrepairworld.blogspot.com/2016/06/how-to-remove-rear-suspension-on-2006.html
This will help.
Thanks

Jun 02, 2016 | 2006 Pontiac Torrent

1 Answer

How do I replace a lower control arm assembly on 04trailblazert


How to Replace an Upper Control Arm - YouTube

? 15:18
https://www.youtube.com/watch?v=wZGr8Xf2ip8
Oct 10, 2014 - Uploaded by ChrisFix
Learn how to replace the Upper Control Arm on a Chevy Trailblazer, GMC ... can you do a video on how to ...

Installing Rubber bushing on lower arm for trailblazer ...

? 0:53
https://www.youtube.com/watch?v=KYIPc_ZXMJo
Jul 27, 2013 - Uploaded by Abdul Hameed
Installing Rubber bushing on lower arm for trailblazer ... How ToChange Control Arm Bushings Using A ...

Nov 28, 2015 | Cars & Trucks

1 Answer

Had help replacing shocks on 2006 Chrysler 300 now have rattle, does washer go on top or bottom of mount


typically a washer will be installed on the shock, then the isolator, jounce, or bushing will be installed, then the other washer will go over that, and then the nut will be installed to tighten everything up.

Sep 04, 2013 | 2006 Chrysler 300

1 Answer

How do i change my rubber bushings on the front suspention of my 1997 dodge ram 1500


opper Control Arm Bushings
  • To access the upper control arm, remove the shock absorber and the strut bar. Also, disconnect the sway bar from the lower control arm, if your particular Ram model is equipped with it. After that, you can hold the coil spring in place with a spring compressor.
    Secure the wheel hub assembly to the chassis using a wire before you disconnect the upper ball joint. This will prevent damage to the brake hose. When ready, release the ball joint using a ball-stud loosening tool (see Resources).
    The upper control arm mounts to the chassis with a cam bolt assembly. Once removed, you can place the control arm on a vise and remove the bushings using a bushing service tool (see Resources). When installing the new bushings, do not use any lubricant but make sure the flange on the bushing end seats properly on the arm bore. Then re-install the upper control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension.
Lower Control Arm Bushings
  • Remove the shock absorber and strut bar. If your particular model is equipped with a sway bar, disconnect it from the lower control arm.
    Secure the coil spring with a spring compressor and release the lower ball joint from the wheel/hub assembly using a ball stud loosening tool (see Resources).
    Now you can release the lower control arm by removing the rear mounting bolts. Remove the bushings with a bushing service tool (see Resources). When installing the new bushings, do not use lubricant and make sure they seat properly on the control arm bore. Then replace the lower control arm. When finished, take your Dodge vehicle to a good shop to align the front suspension

Oct 20, 2011 | Cars & Trucks

1 Answer

How do you change the rear shocks


Support the rear suspensionfrom under the lower suspension arm.
Remove shock absorber upper nut, washer and bushing
Remove lower shock absorber nut and washer.
Remove shock absorber.
Reverse steps to install.

Jan 08, 2011 | 2004 Hyundai Santa Fe

1 Answer

Dear Sir, How do you change an 87 mitsubishi mighty max front shocks without any compression equipment? Please email me at brad8141@hotmail.com. Is there a book with instructions regarding this...


REMOVAL & INSTALLATION
  1. Support the vehicle safely on jackstands. Support it at a height which will allow sufficient room to reach the upper shock absorber mount.
  2. Remove the wheel.
  3. Remove the upper shock nut, washer and bushing.
  4. Remove the lower mounting bolt(s) and remove the shock from the vehicle.
  5. Install the shock absorber in the vehicle and loosely tighten the upper shock absorber nut. Make sure the install the bushings and washers before installing the upper nut.
  6. For 4WD vehicles, install the shock absorber so that the white paint mark at the lower side of the shock absorber faces the outer side of the vehicle. Install the lower shock absorber bolt(s). On 1992-95 Montero torsion bar suspensions, tighten the single lower mounting bolt and nut to 65-76 ft. lbs. (88-103 Nm). On all other vehicles (whether torsion bar or coil spring suspensions), the two lower shock absorber mounting bolts should be tightened only to 7-10 ft. lbs. (9-14 Nm). Fig. 1: Install the shock absorber so that the white mark faces toward the outside of the vehicle - 4WD vehicles, except 1992-95 Monteros 86668006.gif
    Fig. 2: Install the bushings, washers and nuts in the order shown - except 1992-95 Monteros 86668007.gif

  7. On 1992-95 Monteros, tighten the shock absorber installation nut so that the dimensions shown in the illustration ( A and B) are at the standard values. These standard values are: A - 0.04-0.08 in. (1-2mm), B - 0.06-0.10 in. (1.5-2.5mm). WARNING
    When tightening the nut, be careful not to bend the stud pin of the washer assembly.
  8. On all other vehicles, once the lower mounting bolt(s) are tightened, tighten the upper shock absorber mounting nut all the way to the end of the thread on the shock absorber stud, then tighten the locking nut to 9-13 ft. lbs. (12-18 Nm).
  9. Install the wheel.
  10. Lower the vehicle to the ground. Fig. 3: When installing the upper shock nuts on 1992-95 Monteros, make sure measurement A is 0.04-0.08 in. (1-2mm) 86668008.gif
    Fig. 4: When installing the upper shock assembly, make sure its components are positioned as shown - 1992-95 Monteros 86668009.gif
prev.gif next.gif

Nov 03, 2010 | 1987 Mitsubishi Mighty Max

1 Answer

On a 2006 chevy silverado i install new shocks. do i bottom out the front shock bushing thats located at the top of the shock.


  1. Install the upper insulator to the shock absorber.
  2. Install the nut to the tennon end. Do not tighten the nut.
  3. Remove the safety stands.
  4. Lower the vehicle.
  5. Hold the tennon end with a wrench while torquing the nut.
  6. Tighten
    Tighten the nut to 20 N·m (15 lb ft).

Nov 01, 2009 | 2006 Chevrolet Silverado 1500 2WD

2 Answers

2001 Volvo s80 has left/right lower control arms Cracks noticed


the bushings are most likely what he was saying is cracke go to fcp groton .com buy the parts yourself and pay some one to install them it is common

Jul 20, 2009 | 2001 Volvo S80

1 Answer

Clanking noise coming from rear of 99 Jeep Grand Cherokee


check bushings on the pan hard rod and or spring seats

Jun 28, 2009 | 1997 Nissan Maxima

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

Not finding what you are looking for?
2000 Toyota 4Runner Logo

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...