Question about 2001 Chevrolet Silverado 2500HD

1 Answer

Does a faulty crank sensor set a code on a 2001Silverado

Does a faulty crank sensor set a code on a 2001 Silverado 8.1 or can it be faulty without setting a code? Truck quits during highway speeds and low speeds including coming to a stop at an intersection. Sometimes after cutting out at highway speeds during coasting it will restart as you intermittently step on the accelerator. Ignition has to be off for about a minute before it will restart. Sometimes does not start after sitting also. Can take up to an hour before it will restart. Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It should set a diagnostic fault code, but if it does not then take out the sensor and inspect for a crack in it or motor oil in the electrical plug connector which indicates a faulty sensor.

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace crankshaft sensor 2001 intrepid


crank sensor is held to the motor with one bolt. disconnect the plug and remove bolt then sensor. note that Chrysler computers at that time would set codes for the opposite sensor meaning it could be the cam sensor that is faulty.

Jul 14, 2014 | 2001 Dodge Intrepid

1 Answer

1999 chevy silverado with p1345,p0171,andp0174


Did you verify the sensors were faulty before you replaced them ? Code 1345 means the signal from each sensor is not in sync with the other. That means one sensor signal is out of sync, or there is a problem with the timing chain.
Codes 171 and 174 deal with the issue of the fuel system being too lean on both banks or heads. You could have compression or fuel problems that would cause those codes.
A mechanic would use a scanner to monitor data from the sensors and try to figure out whats going on.

Feb 19, 2014 | Cars & Trucks

1 Answer

Can you list all the sensors on 2001silverado 2500 hd and their locations


WOW, there is a ton. I suggest you go to autozone.com, sign up with an email account, and you can access all the repair guides for your truck. I found over 10 diagrams that you could use. autozone.com

Dec 08, 2013 | 2001 Chevrolet Silverado 2500HD

1 Answer

2004 chevy silverado 5.3L V8 runs rough and stalls


Well, code 336 is for a problem with the crank sensor, and code 171 is for fuel system too lean bank one which is the side with cylinder one. Since you have checked fuel pressure and I will assume fuel volume is good, the crank sensor or circuit could be at fault.

Jul 09, 2013 | Cars & Trucks

1 Answer

Miss in 1999 silverado 2500 6 liter


It sounds like you may have a small block in your fuel system. When was the last time you changed your fuel filter out?

Nov 12, 2011 | 1999 Chevrolet Silverado 2500

1 Answer

2000 chevy silverado 5.3, skips a little between 50-55mph, plugs and wires were changed. scanner shows bad knock sensor #2. will changing this correct the problem?


it should but recheck ur wires and plugs first a bad plug or wire can cause a knock ping problem and set off sensor also check the knock sensor connections at rear of engine----- the knock sensors for the 8 cyl are located under the intake manifold so its labor intensive to replace the sensor

Aug 22, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Looking for the location of the crank position sensor and the knock sensor for a 2001 chevrolet silverado with a 4.8 8cylinder engine


Crank sensor; right (pass.) side of block above the starter. You may have to remove the starter to remove the crank sensor.

Knock sensor: There may be 2, a front and a rear. Both would be UNDER the intake manifold on top of the engine block one behind the other about 8 inches or so apart. The manifold and associated item may or may not need to be removed to access the sensors.

Aug 10, 2009 | 2001 Chevrolet Silverado

1 Answer

2002 Chevy Silverado, crank sensor installed. can't start truck.


After installing a new crank sensor, a Tech 2 will need to be hooked up in order to complete what is called a relearn procedure on the new crank sensor. Until this is done, your truck's ECM is unable to determine when cylinder #1 is at TDC and electronic timing is unable to be performed. Need to tow to GM dealership for this proceedure.

Jun 17, 2009 | 2001 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...