Question about 1990 Nissan Pulsar

1 Answer

How to remove cv 1994 pulsar to replace outer d/side boot

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

  1. Raise the front of the vehicle and support it on jackstands, then remove the wheel and the tire assembly.
  2. Remove the cotter pin from the drive axle.
  3. Have a helper firmly apply the brakes, and loosen the hub nut.
  4. Remove the caliper assembly.

It is not necessary to disconnect the brake hose from the caliper. Position the caliper out of the way and secure with mechanics wire.
  1. Using the removal tool HT72520000 or equivalent, remove the tie rod ball joint from the steering knuckle.
  2. On 1982-86 vehicles, disconnect the ball joint from the lower control arm, by removing the mounting nuts from the bottom of the control arm.
  3. On 1987-90 vehicles, disconnect the ball joint from the steering knuckle, using removal tool HT72520000 or equivalent.
  4. Using a block of wood and a mallet, separate the halfshaft from the hub/steering knuckle assembly. If the assembly is difficult to separate it may be necessary to use a press/puller tool.

In order to protect the halfshaft from damage, it is a good idea when striking the halfshaft, to temporarily install the hub nut.
  1. Drain the lubricant from the transaxle.
  2. Support the engine properly and remove support bracket if so equipped.
  3. Remove the halfshaft from the right side on automatic transaxle equipped vehicles and on all manual transaxles as follows:
    1. Insert a suitable prybar between the inner CV-joint and the transaxle.
    2. Carefully pry the halfshaft from the transaxle.


When removing the driveshaft from the transaxle, do not pull on the driveshaft. The driveshaft will separate at the sliding joint (damaging the boot).
  1. Remove the left side halfshaft on automatic transaxles as follows:
    1. Remove the right side halfshaft as outlined above.
    2. Insert a slotted screwdriver, from the right side of the transaxle.


Make certain that the screwdriver is properly aligned into the slot in the halfshaft.
  1. Tap the screwdriver with a mallet to remove the left side halfshaft from the transaxle.

  1. Pull the hub/steering knuckle assembly away from the vehicle and remove the halfshaft from the transaxle.

After removing the halfshaft from the transaxle, be sure to install a holding tool to hold the side gear in place while the axle is removed.
To install:
  1. Always use a new circlip on the driveshaft and install a new oil seal to the transaxle.
  2. Install the halfshaft into the transaxle.

When installing the driveshaft into the transaxle, use oil seal protector tool KV38105500 or equivalent to protect the oil seal from damage; after installation, remove the tool.
  1. Align the halfshaft with the hub/knuckle assembly and connect the lower control arm-to-ball joint.
  2. On 1982-86 vehicles, connect the lower control arm to the ball joint and tighten the control arm-to-ball joint nuts to 40-47 ft. lbs. (54-64 Nm).
  3. On 1987-90 vehicles, connect the lower ball joint to the steering knuckle and tighten the stud nut to 43-54 ft. lbs. (59-74 Nm).
  4. Connect the tie rod to the steering knuckle and torque the tie rod stud nut to 22-36 ft. lbs. (30-49 Nm).
  5. Install then hub nut and tighten to 87-145 ft. lbs. (118-197 Nm).
  6. Install new cotter pin in drive axle and mount the caliper assembly.
  7. Install the wheel and tire assembly.
  8. Road test for proper operation.

Posted on Nov 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace outer cv boot on alfa 156


Remove tire, remove brake caliper, and hang on suspension with a tie, remove lower suspensin from lower A-Arm, then with a "Breaker Bar" or Impact Gun Remove the nut in the center of your rotor, and you should be able to remove the axle from the hub. The old CV boot you can just cut off, and after a good clean, reinstall the new boot (I recommend you add some CV Grease as long as it's exposed to lubricate the joint), then slide new boot on.

Sep 24, 2014 | 2004 Alfa Romeo 156

1 Answer

How to replace the front outer boot


The outer CV-joint boot can be serviced or replaced by removing the inner CV-joint. Click this link below for replacing instructions:--- http://repairhelpcenter.blogspot.com/2011/10/how-to-replace-front-drive-axle-cv.html ----------- This will help.Thanks.Helpmech.

Oct 17, 2011 | 2003 Chevrolet Tracker

1 Answer

When makeing a left turn clicking.


this is the sign of a failing outer CV joint in the drive shaft. look under car at driveshaft. the rubber boot around CV joint is probably torn. This allows lube to fling out and water to come in, contaminating the CV joint. Replace the entire drive shaft instead of replacing only the outer CV joint.

Nov 11, 2010 | 1994 Plymouth Voyager

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

I've got a 1999 2500 Chevy Silverado , that I need to change a cv boot on , can u assist me.?


CV-Joints
Overhaul
These vehicles use several different types of joints. Engine size, transaxle
type, whether the joint is an inboard or outboard joint, even which side of the
vehicle is being serviced could make a difference in joint type. Be sure to
properly identify the joint before attempting joint or boot replacement. Look
for identification numbers at the large end of the boots and/or on the end of
the metal retainer bands.

The 3 types of joints used are the Birfield Joint, (B.J.), the Tripod Joint
(T.J.) and the Double Offset Joint (D.O.J.).

NOTE: Do not disassemble a Birfield joint. Service with a new joint or
clean and repack using a new boot kit.

The distance between the large and small boot bands is important and should
be checked prior to and after boot service. This is so the boot will not be
installed either too loose or too tight, which could cause early wear and
cracking, allowing the grease to get out and water and dirt in, leading to early
joint failure.

NOTE: The driveshaft joints use special grease; do not add any grease
other than that supplied with the kit.

Double Offset Joint
To Remove:

NOTE: The Double Offset Joint (D.O.J.) is bigger than other joints
and, in these applications, is normally used as an inboard joint.


  1. Remove the halfshaft from the vehicle.
  2. Side cutter pliers can be used to cut the metal retaining bands. Remove the
    boot from the joint outer race.
  3. Locate and remove the large circlip at the base of the joint. Remove the
    outer race (the body of the joint).
  4. Remove the small snap ring and take off the inner race, cage and balls as an
    assembly. Clean the inner race, cage and balls without disassembling.
  5. If the boot is to be reused, wipe the grease from the splines and wrap the
    splines in vinyl tape before sliding the boot from the shaft.
  6. Remove the inner (D.O.J.) boot from the shaft. If the outer (B.J.) boot is
    to be replaced, remove the boot retainer rings and slide the boot down and off
    of the shaft at this time.

To Install:

NOTE: Be sure to tape the shaft splines before installing the boots.
Fill the inside of the boot with the specified grease. Often the grease supplied
in the replacement parts kit is meant to be divided in half, with half being
used to lubricate the joint and half being used inside the boot.


  1. Install the cage onto the halfshaft so the small diameter side of the cage
    is installed first. With a brass drift pin, tap lightly and evenly around the
    inner race to install the race until it comes into contact with the rib of the
    shaft. Apply the specified grease to the inner race and cage and fit them
    together. Insert the balls into the cage.
  2. Install the outer race (the body of the joint) after filling with the
    specified grease. The outer race should be filled with this grease.
  3. Tighten the boot bands securely. Make sure the distance between the boot
    bands is correct.
  4. Install the halfshaft to the vehicle.

Except Double Offset Joint
To Remove:


  1. Disconnect the negative battery cable. Remove the halfshaft.
  2. Use side cutter pliers to remove the metal retaining bands from the boot(s)
    that will be removed. Slide the boot from the T.J. case.
  3. Remove the snap ring and the tripod joint spider assembly from the
    halfshaft. Do not disassemble the spider and use care in handling.
  4. If the boot is be reused, wrap vinyl tape around the spline part of the
    shaft so the boot(s) will not be damaged when removed. Remove the dynamic
    damper, if used, and the boots from the shaft.

To Install:


  1. Double check that the correct replacement parts are being installed. Wrap
    vinyl tape around the splines to protect the boot and install the boots and
    damper, if used, in the correct order.
  2. Install the joint spider assembly to the shaft and install the snap ring.
  3. Fill the inside of the boot with the specified grease. Often the grease
    supplied in the replacement parts kit is meant to be divided in half, with half
    being used to lubricate the joint and half being used inside the boot. Keep
    grease off the rubber part of the dynamic damper (if used).
  4. Secure the boot bands with the halfshaft in a horizontal position. Make sure
    distance between boot bands is correct.
  5. Install the halfshaft to the vehicle and reconnect the negative battery
    cable.






Check the CV-boot for wear
tccs7030.jpg








Removing the outer band from the CV-boot
tccs7031.jpg








Removing the inner band from the CV-boot
tccs7032.jpg








Removing the CV-boot from the joint housing
tccs7033.jpg








Clean the CV-joint housing prior to removing boot
tccs7034.jpg








Removing the CV-joint housing assembly
tccs7035.jpg








Removing the CV-joint
tccs7036.jpg








Inspecting the CV-joint housing
tccs7037.jpg








Removing the CV-joint outer snap ring
tccs7038.jpg








Checking the CV-joint snap ring for wear
tccs7039.jpg








CV-joint snap ring (typical)
tccs7040.jpg








Removing the CV-joint assembly
tccs7041.jpg








Removing the CV-joint inner snap ring
tccs7042.jpg








Installing the CV-joint assembly (typical)
tccs7043.jpg




prev.gif next.gif

Oct 07, 2010 | 2002 Chevrolet Silverado 2500HD

2 Answers

Where is the cv joint


Hello harborviewdo. My name is Roger and i will answer your question. Your vehicle has two drive axle half shafts. One on each side of the transmission. The out board side of each shaft is called the outer cv joint. Generally when they are bad you will find the outer boot is torn and has thrown the grease out. Should you need further help please just ask. Please rate the answer you received. This way I know it was helpful. Thank you for using Fix Ya. Roger

Jun 28, 2010 | 1994 Dodge Intrepid

3 Answers

When replacing a outer C.V joint boot , do you


you can replace just the outter but you may want to replace the whole axle alot easier

Jan 17, 2010 | 1993 Ford Festiva

1 Answer

Trying to get the bearing off of the cv axle 1994 camry


I think you mean cv joint. If so, a new axle cost $59. You are doing alot of extra work and the joints could be damaged. The outer joint comes off, but it takes a large hammer. The inner joint usually has an inboard ring clip that you pop out with a screwdriver.

Mar 25, 2009 | 1994 Toyota Camry

1 Answer

CV replacement


You don't have to pull the hub! No spring compressor needed. Either unhook the steering knuckle from the strut or thre lower ball joint and swing it out away from the car. Remeber to remove the brake calipers and tie rod ends to get more "swing". It takes a little palying with to manuver it out but you can do it.

Dec 26, 2008 | 1990 Nissan Pulsar

Not finding what you are looking for?

Open Questions:

See all 1990 Nissan Pulsar Questions

1990 Nissan Pulsar Logo

603 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...