Question about 2001 Chevrolet Silverado 2500HD

1 Answer

The oil sensor needs to be replaced where is it

The oil sensor needs to be replaced where is it located on the 8100 engine year is2001

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 97 Answers

  1. Remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.

    the oil sensor needs to be replaced where is  it - 0996b43f802053c4.jpg enlargethe oil sensor needs to be replaced where is  it - enlarge_tooltip.gif_mienlarge_tooltip.gif Fig. Using J 41712 or equivalent, remove the oil pressure sensor-8.1L engines

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    1. Tighten the sensor to 22 ft. lbs. (30 Nm).

  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.

Posted on Nov 15, 2009

  • Hayden Ford
    Hayden Ford Nov 15, 2009

    oil pressure sensor

  • Hayden Ford
    Hayden Ford Nov 15, 2009

    this is all i could find for a location on a oil level sensor. it's for a 6.0L but see if its the same

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

98 buick lesabre oil pressure dropped to 0 and engine died. added 1 quart oil, waited 30 minutes, started and drove 5 miles then oil pressure dropped to 0 and engine died. does this sound like a bad oil...


my sister had the same problem. There are 2 sensors that can cause this when they go bad. One is the oil pressure switch, which is located near the oil filter. When the PCM reads this switch, and gets a low reading, it will automatically kill the engine. The switch costs around $4.00 and is a 5 minute replacement job. The other possibility is that the crank position sensor has gone bad. When this sensor goes bad, the PCM can't read the appropriate speeds of the crankshaft, and will adjust the fuel and air mixture to compensate, often times the engine will die because it is getting insufficient fuel and air. The Crank position sensor is located on the engine block near the water pump. It is around $40.00 and at the most a 30 minute replacement job if you are unfamiliar with the process. I hope this helps. I'm a vehicle mechanic in the Air Force, with roughly 7 years of experience on the floor.

Oct 16, 2010 | 1998 Buick LeSabre

2 Answers

I AM LOOKING WHERE IS THE OIL PUMP IN 2003 KIA SEDONA ENGINE


take the sump off and you will find it ,to get the sump off you will need to remove the engine

Jun 27, 2010 | 2003 Kia Sedona

2 Answers

1999 Jeep Cherokee Sport 4.0L engine. Oil


I'm assuming the engine is still running and no engine noise has occured due to loss of oil pressure, and it is just the gauge that is not reading? If so, the oil pressure switch that is located on the camshaft sensor, could have a bad connection or the oil sensor will need to be replaced. The oil sensor is located on the left side of the engine and is mounting horizontally on the camshaft sensor housing.

Apr 08, 2010 | 1999 Jeep Cherokee

1 Answer

Where is the oil sending unit on a 1996 ford taurus 3.0 liter engine located? glenn


On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Feb 18, 2010 | 1996 Ford Taurus

1 Answer

Troubleshooting no. po118 po705 po301 i need to


P0118 - Engine Coolant Temperture Sensor - Circuit High Input
P0301 - Cylinder 1- Misfire Detected
P0705 - Transmission Range Sensor Switch Circuit Malfuction (PRNDL Input)

P0118 - Replace Engine coolant Temperture sensoe located by thermostat housing (upper ragiator hose connects to) sensor is 1 where wire loom lays nect to valve cover.

P0301 - bad spark plug/wire, remove #1 cylinder plug wire inspect for oil on wire (if have oil on wire, valve cover gasket leaking, needs to be replaced) if no oil, inspect plug, replace plugs if needed.

P0705 - bad neutral safty switch (Transmission Range Switch) located on Right Side of Automantic Transmission (by shifter cable)

Feb 09, 2010 | 1998 Kia Sportage

2 Answers

98 ford explorer oil pressure sensor location


2.9L and 4.0L engines-Left side front of the engine, below the cylinder head in the engine block

237d46d.jpg

Nov 28, 2009 | 1998 Ford Explorer

1 Answer

Oil sensor


The oil light on your car has nothing to do with oil level in the crankcase but rather oil pressure. The oil pressure switch/sensor is located on the rear of the engine block above the right axle I believe. Unless you have engine noise or suspect low oil pressure, I'd replace it but you could check oil pressure for peace of mind with an pressure gauge if you wish. You may need a special socket to replace it.

Oct 18, 2008 | 2001 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

1,020 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...