Question about 1998 Chevrolet Blazer

1 Answer

Dipstick tube leaking

I have a 98 chevy blazer 4x4 i changed the moter it runs good but the dipstick tube on the tranny is leaking i put a new rubber gasket on it and changed the dipstick tube but it still leaks

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Cheek to make sure its not over full also the trans lines r right there make sure it not them spayin over after all u just did the motor and the trans was most likly hangin

Posted on Nov 27, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Chevy blazer 6cyl 4x4 , car hesitates between 1500-2000 rpms


hesitation (flat spot) was common with cars sporting carbys
as it should be an EFI controlled engine then run the fault codes and look for accelerator position sensor., throttle motor , MAF/VAF sensors

Aug 19, 2015 | Cars & Trucks

1 Answer

On my 93 chevy s10 4x4 blazer, my instrument panel worked before new motor was put in, after having the new engine put in, my fuel gauge, oil pressure, voltmeter, rpm, and my temp gauge all quit worki


Look for a missing ground strap from the engine to the body or frame. Remember the engine sits on rubber mounts so that ground strap is essential.

Feb 21, 2014 | Cars & Trucks

1 Answer

95 chevy blazer 4x4, 4.3, v6, tranny fluid flows out top of fill tube. I have changed the filter and no I did not overfill it. Starts right up even when cold, but starts losing fluid right away (drove...


There should be a vent tube on your transmission. Check to make sure it is not plugged. Did it do it before you changed the fluid and filter? To properly check fluid level the vehicle needs to be running and warm and in park on a level surface. Just in case you didn't already know. IF your vent tube is open and fluid level is correct you must have internal problems.

Apr 22, 2011 | 1995 Chevrolet Blazer

2 Answers

Will a 1990 chevy 1500 truck 4x4 transmission fit in a 1997 4x4 chevy tahoe


yes it will as long as it is the same model transmission. As long as you get a transmission out of a standard cab truck you should be ok. ( for a good idea Most 88-98 gm trucks, full size blazers,jimmys,tahoes, and yukons will interchange) same chassis just different bodys and emblems

Feb 27, 2011 | Chevrolet Tahoe Cars & Trucks

1 Answer

I have a 98 chevy blazer and the checkengen light is on and the coades are po115, po174, po300, and po1153. I have changed two o2 sensers and the catalacconverter and the plugs and wires. I reset the...


More than likely, you've got a leaking or deteriorated PCV tube connection (hole in a vacuum hose) which will cause the engine to run a little rought at idle. Look for a small hole in any rubber hoses between the PCV valve on the crankcase and the engine's intake near the firewall at the back of the motor. This should resolve the PO174 (fuel trims) code and PO300 (misfires). Also the PO1153 has to do with exhaust sensors and since you've changed the sensors you probably have an exhaust leak before the sensor, probably a bad exhaust header gasket.
Now

Jul 25, 2010 | 1998 Chevrolet Blazer

1 Answer

I just replaced a transmision on a l998 Chevy Blazer and when I put it in gear it barely moves what could be the problem. I filled it up with transmition fluid. Could it be the Torque Converter? Or could...


Proper way to fill tranny after instalation of a new one is to fill to fill line before starting motor. Once it is full, read the dipstick. It will say to check with motor running and either in neutral or park. Clean off the dip stick and take a reading with motor running and tranni in proper position. Keep filling and rechecking untill it reads full while running and tranni in proper position. Once completely filled should run fine if the kickdown cable, aka tv cable, is adjusted properly.

Feb 21, 2010 | 1998 Chevrolet Blazer

1 Answer

Tranny leak


THE TUBE IS A VENT YOU HAVE PRESSURE BUILD UP WAS THIS WHILE TOWING

May 16, 2009 | 2000 Chevrolet Blazer

1 Answer

Take out the tranny on a 1995 chevy blazer


Yeah Go Buy The Repair Manual And A 24 Pack.

Jan 22, 2009 | 1995 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...